Audi S5 CABRIOLET Owner'S Manual Download Page 251 | Manualshive

Page: 251 / 294

background image

Self-help

249

Controls

Safety

Driving tips

General maintenance

Self-help

Technical data

– Ensure that all passengers leave the vehicle and move

away from the danger area

⇒

.

– Take the tyre sealant can and the electric compressor out

of the luggage compartment

⇒

page 245.

– Fix the sticker “max. 80 km/h”, which is included with the

tyre sealant can, onto the instrument cluster where the
driver will see it.

Filling the tyre

– Shake the tyre sealant can well.

– Screw the enclosed filling hose onto the sealant can as

far as it will go. This will automatically pierce the foil
sealing the can.

– Take the valve cap off the tyre valve and use the enclosed

valve insert tool to unscrew the valve insert

⇒

page 248,

fig. 228.

– Place the valve insert onto a clean surface.

– Remove the sealing plug from the filling hose and insert

the hose into the tyre valve.

– Hold the tyre sealant can upside down and fill the

complete contents of the can into the tyre.

– Then disconnect the hose and screw the valve insert

firmly back into the tyre valve.

Inflating the tyre

– Screw the filling hose of the electric compressor onto the

tyre valve and plug the connector into the cigarette
lighter.

– Pump the tyre up to 2.0 to 2.5 bar and monitor the pres-

sure shown on the pressure gauge.

– If the tyre pressure remains lower than the value speci-

fied above drive the vehicle approx. 10 metres forwards
or backwards, so that the sealant can spread evenly in
the tyre. If the pressure is still lower than the specifica-
tion the tyre is too badly damaged and cannot be
repaired using the tyre sealant.

Final checks

– After about 10 minutes stop to check the tyre pressure.

– If tyre pressure is less than 1.3 bar, the tyre is too badly

damaged. Do not drive on. You should obtain profes-
sional assistance.

WARNING

•

If you have a puncture in moving traffic, switch on the hazard

warning lights and place the warning triangle in a visible location.
This is for your own safety and also warns other road users.

•

Make sure your passengers wait in a safe place (for instance

behind the roadside crash barrier).

•

Please observe the manufacturers' safety notes on the

compressor and the instructions supplied with the tyre sealant
can.

•

If it was not possible to build up a tyre pressure of 2.0 bar

within 6 minutes this means that the tyre is too badly damaged.
Do not drive on.

•

Seek professional assistance if the repair of a tyre puncture is

not possible with the sealing compound.

•

If tyre pressure is less than 1.3 bar after driving about 10

minutes, the tyre is too badly damaged. Do not drive on. You
should obtain professional assistance.

document_0900452a81793dcc.book Seite 249 Mittwoch, 21. März 2007 5:42 17

«
...
249
250
251
252
253
...
»

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Reviews:

No comments

Related manuals for S5 CABRIOLET

Brand: TBC Pages: 12

Brand: Gatorback Mudflaps Pages: 4

VIEWLINE 52 MM - MOUNTING 11-09

Brand: VDO Pages: 4

Brand: Menabo Pages: 12

Brand: Whispbar Pages: 15

Brand: QA1 Pages: 3

2008 Savana Van

Brand: GMC Pages: 402

Brand: Honda Pages: 330

Brand: DICE Pages: 1

Brand: Hudson Pages: 24

MagicWatch MWE850

Brand: Waeco Pages: 200

Brand: TrailFX Pages: 3

Brand: Cadillac Pages: 508

Brand: Kia Pages: 289

Brand: Toyota Pages: 277

Brand: Honda Pages: 234

Brand: AutoMaxi Pages: 2

Brand: Steinhof Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands