Audi S5 CABRIOLET Owner'S Manual Download Page 254

Page: 254 / 294

Self-help

252

Loosening

– Fit the box spanner as far as it will go over the wheel

bolt

– Grip the box spanner as close to the end as possible and

turn the wheel bolts about one turn anti-clockwise

⇒

page 251, fig. 230 -arrow-.

Tightening

– Fit the box spanner as far as it will go over the wheel

bolt

– Grip the box spanner as close to the end as possible and

tighten the bolt firmly by turning clockwise.

WARNING

To avoid accidents, the wheel bolts should only be loosened
slightly (about one turn) before raising the vehicle with the jack*.

Note

•

Do not use the hexagonal socket in the screwdriver handle to

loosen or tighten the wheel bolts.

•

If the wheel bolt is very tight, it may be possible to loosen it by

pushing down the end of the spanner carefully with your foot. Hold
on to the car for support and take care not to slip.

Raising the vehicle

The vehicle must be raised with the jack* to remove the
wheel.

Each jacking point is marked by a recess underneath the
vehicle

⇒

fig. 231.

– Place the jack underneath the jacking point closest to

the wheel being changed. Make sure the base plate

flat on the ground.

– Wind up the jack by the knob

until the claw of the jack

completely surrounds the seam on your vehicle

⇒

fig. 232.

An adapter is required to unscrew or tighten the anti-theft wheel bolts*

⇒

page 254.

Fig. 231 Changing a
wheel: Jacking points

Fig. 232 Changing a
wheel: Jack

document_0900452a81793dcc.book Seite 252 Mittwoch, 21. März 2007 5:42 17

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Search results

Summary of Contents for S5 CABRIOLET

Reviews:

Related manuals for S5 CABRIOLET

Brands by name

Popular brands

Audi S5 CABRIOLET, Owner'S Manual

Search results

Summary of Contents for S5 CABRIOLET

Reviews:

Related manuals for S5 CABRIOLET

Brands by name

Popular brands