Audi S5 CABRIOLET Owner'S Manual Download Page 218 | Manualshive

Page: 218 / 294

background image

Care of vehicle and cleaning

216

Applies to vehicles: with Alcantara seat covers

Cleaning Alcantara

Removing dust and dirt

– Moisten a cloth just a little and wipe down the seat

covers.

Removing stains

– Moisten a cloth with lukewarm water or diluted methyl-

ated spirits.

– Dab at the stain. Start at the outside and work inwards.

– Dry the area you have cleaned with a soft cloth.

Do not use leather cleaning products on Alcantara seat covers.

You may use a suitable shampoo on dust and dirt.

Dust and grit in the pores and seams can have an abrasive effect
and damage the surface of the leather. If the car is left standing in
the sun for long periods, the leather should be protected against
direct sunlight to prevent it from fading. However, slight colour vari-
ations will arise in normal use.

Caution

•

Do not use solvents, wax polish, shoe cream, stain removers,

leather cleaning products or any similar products on Alcantara.

•

To avoid damage, stubborn stains should be removed by a qual-

ified workshop.

•

On no account use brushes, hard sponges or similar utensils.

Seat belts

Seat belts should be looked after properly to ensure that
they give the full protection.

– Keep the seat belts clean.

– For cleaning, use a mild soap solution.

– Check the condition of the seat belts at regular intervals.

Very dirty belts may not retract properly.

Make sure that the inertia reel seat belts are completely dry before
allowing them to retract.

Caution

•

Do not remove the seat belts from the vehicle to clean them.

•

Do not use chemical cleaning agents on the seat belts, as this

can damage the webbing. Ensure that the belts do not come into
contact with corrosive fluids.

•

If you find any damage to the belt webbing, belt fittings, the belt

retractor or the buckle, the belt in question must be replaced by a
qualified workshop.

document_0900452a81793dcc.book Seite 216 Mittwoch, 21. März 2007 5:42 17

«
...
216
217
218
219
220
...
»

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Reviews:

No comments

Related manuals for S5 CABRIOLET

Brand: Daihatsu Pages: 41

Brand: Daihatsu Pages: 268

Brand: iDataLink Pages: 30

PRIME DESIGN VCR 326

Brand: Safe Fleet Pages: 16

Prime Design VBC PC11

Brand: Safe Fleet Pages: 8

Prime Design AR1418

Brand: Safe Fleet Pages: 4

Brand: Bestop Pages: 11

Brand: Whispbar Pages: 14

2014 Insignia VXR SuperSport

Brand: Vauxhall Pages: 56

Brand: Axxess Pages: 4

Brand: Vintage Air Pages: 14

Brand: Ford Pages: 38

Brand: Whispbar Pages: 14

Brand: Sears Pages: 41

Brand: Axxess Pages: 8

Brand: Dodge Pages: 276

Brand: Belkin Pages: 2

MultiCharger 1204

Brand: DEFA Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands