manualshive.com logo in svg

Audi S5 CABRIOLET, Owner'S Manual

The Audi S5 Cabriolet's Owner's Manual is available for free download on manualshive.com. This comprehensive manual provides essential information and guidance on operating and maintaining your Audi S5 Cabriolet. Get the most out of your vehicle's features and ensure a smooth driving experience with this informative manual.

Share
Download
background image

Towing a trailer

198

Towing a trailer

Driving the vehicle with a trailer or 
caravan

Technical requirements

The towing bracket must comply with certain technical 
requirements.

Your car is intended mainly for transporting passengers and 
luggage. However, if suitably equipped, it can also be used to tow a 
trailer or caravan.

If the car is supplied with a factory-fitted towing bracket it will 
already have the necessary technical modifications and meet the 
statutory requirements.

A 13-pin socket is provided to make the electrical connection 
between the car and the trailer. If the trailer has a 7-pin plug you can 
use an adapter cable. This is available from Audi dealers.

WARNING

If a towing bracket is retrofitted, the installation should be carried 
out by a qualified workshop.

•

In particular in high outside temperatures it is not possible to 

drive up long steep gradients without a suitable cooling system. 
The engine would then overheat.

•

Incorrect installation can result in a safety risk.

Points to check before towing

Trailer weights

Never exceed the maximum permitted trailer weights 

⇒

page 281.

If you do not load the trailer up to the maximum permitted trailer 
weight, you can then climb correspondingly steeper gradients.

The maximum trailer weights listed are only applicable for altitudes 
up to 1000 m above sea level. With increasing altitude the engine 
power and therefore the car's climbing ability are impaired because 
of the reduced air density, so the maximum trailer weight has to be 
reduced accordingly. The weight of the car and trailer must be 
reduced by 10% for every further 1000 m (or part thereof). This 
figure refers to the combined weight of the (loaded) vehicle and 
(loaded) trailer.

The figures for the draw bar weight that appear on the identification 
plate of the towing bracket are for certification purposes only. The 
correct figures for your specific vehicle, which may be lower than 
these figures for the towing bracket, are given in the registration 
documents. Also refer to 

⇒

page 281.

Distributing the load

Distribute loads in the trailer so that heavy objects are as near to the 
axle as possible. Loads carried in the trailer must be secured to 
prevent them slipping.

Where possible, operate the trailer with the maximum permitted 
draw bar weight on the ball joint of the towing bracket, but do not 
exceed the specified limit.

Tyre pressure

Check the tyre pressures on your car and adjust for “full load” condi-
tions (refer to the sticker listing the tyre pressures on the end face 
of the driver's door). It may also be necessary to adjust the tyre pres-
sures on the trailer according to the recommendations of the trailer 
manufacturer.

Exterior mirrors

Check whether you can see enough of the road behind the trailer 
with the standard mirrors. If this is not the case you should have 

document_0900452a81793dcc.book  Seite 198  Mittwoch, 21. März 2007  5:42 17

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Reviews:

No comments

Related manuals for S5 CABRIOLET

Baja Designs S8 Instructions Manual preview
S8
Brand: Baja Designs Pages: 6
VEAP SHIELD UNITED FT Series Mounting Instruction preview
FT Series
Brand: VEAP SHIELD UNITED Pages: 3
Yamaha Yamaha Rhino 660 Instruction Supplement preview
Yamaha Rhino 660
Brand: Yamaha Pages: 3
FORM FIT SD 13R07-5 Installation Instructions preview
SD 13R07-5
Brand: FORM FIT Pages: 2
Thule Edge Flush Rail Instructions Manual preview
Edge Flush Rail
Brand: Thule Pages: 12
SuperATV AAB-P-RZR900-K2-001 Installation Instructions preview
AAB-P-RZR900-K2-001
Brand: SuperATV Pages: 3
Safe Fleet RVS-218627 Instruction Manual preview
RVS-218627
Brand: Safe Fleet Pages: 38
Yakima Whispbar K887W Fitting Instructions Manual preview
Whispbar K887W
Brand: Yakima Pages: 19
Nav TV UCI-11C NTV-KIT331 User Manual preview
UCI-11C NTV-KIT331
Brand: Nav TV Pages: 4
muth signal mirror 2005-2009 Ford Mustang Installation Instruction preview
signal mirror 2005-2009 Ford Mustang
Brand: muth Pages: 9
STC 552-010 Installation Instructions Manual preview
552-010
Brand: STC Pages: 6
Road Ranger H392 Installation Manual preview
H392
Brand: Road Ranger Pages: 22
Great Wall WEY VV5 Service Manual preview
WEY VV5
Brand: Great Wall Pages: 18
WIX WP9378 Installation Instruction preview
WP9378
Brand: WIX Pages: 2
Motoalliance Denali MA11705 Manual preview
Denali MA11705
Brand: Motoalliance Pages: 5
Havis-Shields 1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P Datasheet preview
1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P
Brand: Havis-Shields Pages: 1
Lexus HS 250h Vehicle Dismantling Manual preview
HS 250h
Brand: Lexus Pages: 34
Toyota 86 2020 Quick Reference Manual preview
86 2020
Brand: Toyota Pages: 32

Brands by name

Popular brands

Load more brands