Audi S5 CABRIOLET Owner'S Manual Download Page 223 | Manualshive

Page: 223 / 294

background image

Checking and topping up fluids

221

Controls

Safety

Driving tips

General maintenance

Self-help

Technical data

Working on components in the engine
compartment

Extra caution is necessary when working on components
in the engine compartment.

Always be aware of the danger of injury and scalding as well as the
risk of accident or fire when working in the engine compartment
(e.g. when checking and refilling fluids). Always observe the warn-
ings listed below and follow all normal safety precautions. The
engine compartment of any motor vehicle is a potentially
hazardous area.

⇒

.

WARNING

•

Switch off the engine.

•

Remove the ignition key.

•

Apply the parking brake.

•

Move the gear lever into neutral.

•

Wait for the engine to cool down.

•

Keep children away from engine compartment.

•

Never spill fluids on hot engine components. These fluids can

cause a fire (e.g. radiator anti-freeze).

•

Take care not to cause short circuits in the electrical system,

especially when working on the battery.

•

Do not touch the radiator fan when the engine is hot. The fan

may start running suddenly.

•

Do not unscrew the cap on the expansion tank when the engine

is hot. The cooling system is under pressure.

•

Protect face, hands and arms by covering the cap with a large,

thick rag to protect against escaping coolant and steam.

•

If any tests have to be performed with the engine running,

there is an extra safety risk from the rotating parts, such as the
drive belts, alternator and radiator fan, etc., and from the high-
voltage ignition system.

•

Observe the following additional warnings if work on the fuel

system or the electrical system is necessary:

−

Always disconnect the battery.

−

Do not smoke.

−

Never work near naked flames.

−

Always keep an approved fire extinguisher immediately

available.

Caution

When topping up fluids make sure the correct fluid is put into the
correct filler opening. This can otherwise cause serious malfunc-
tions or engine damage.

For the sake of the environment

Inspect the ground underneath your vehicle regularly so that any
leaks are detected at an early stage. If you find oil spots or other
fluids, have your vehicle inspected by a qualified workshop.

Note

On right-hand drive vehicles* some of the containers/ reservoirs
mentioned below are located on the other side of the engine
compartment.

Closing the bonnet

– To close the bonnet, pull it down to overcome the spring

pressure.

– Then let it drop into the catches; do not press down

⇒

.

WARNING (continued)

document_0900452a81793dcc.book Seite 221 Mittwoch, 21. März 2007 5:42 17

«
...
221
222
223
224
225
...
»

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Reviews:

No comments

Related manuals for S5 CABRIOLET

STRONGARM RVR303

Brand: Blue Giant Pages: 48

Brand: Hama Pages: 40

Brand: TATA Motors Pages: 236

StreetLine Series

Brand: SAAS Pages: 4

Brand: Flash Cover Pages: 2

Brand: ULTIMATE SPEED Pages: 50

Brand: U.S. General Pages: 8

Brand: Volvo Pages: 42

1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P

Brand: Havis-Shields Pages: 1

Brand: SilverLeaf Electronics Pages: 16

SANICON TURBO 300

Brand: Thetford Pages: 25

Brand: Gator Pages: 6

Brand: Subaru Pages: 32

Brand: INDIWORK Pages: 18

Brand: Opel Pages: 103

K40 Platinum360

Brand: K40 ELECTRONICS Pages: 11

Brand: Volvo Pages: 10

Brand: Suzuki Pages: 504

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands