Audi S5 CABRIOLET Owner'S Manual Download Page 116 | Manualshive

Page: 116 / 294

background image

Driving

114

Driving

Steering

Applies to vehicles: with manually adjustable steering column

Adjusting the steering wheel position

The height and reach of the steering wheel can be
adjusted as required to suit the driver.

– Pull the lever

⇒

fig. 130 -arrow-

⇒

up.

– Move the steering wheel to the desired position.

– Then push the lever towards the steering column until

the catch engages.

WARNING

•

Never adjust the position of the steering wheel when the

vehicle is moving - this could cause an accident.

•

For safety reasons, the lever must be pushed securely against

the steering column to prevent the steering wheel from acciden-
tally changing position while driving (accident risk).

Ignition lock

Starting the engine with the key

The ignition key is used to start the engine.

– Insert the key into the ignition lock.

– Manual gearbox: Press the clutch pedal all the way down

and move the gear lever into neutral.

– Automatic gearbox: Press the brake pedal and move the

selector lever to position P or N.

– Press in the key

⇒

fig. 131 to start the engine.

If you press in the key without pressing the clutch or brake pedal,
the ignition will be switched on or off. The steering lock is released
when the ignition is switched on.

The key can be removed only when the ignition is off. The key has to
be pressed in briefly to switch off the ignition. On vehicles with an
automatic gearbox, the selector lever has to be in position P.

Electrical components with a high power consumption are switched
off temporarily while you start the engine.

Fig. 130 Lever beneath
steering column

Fig. 131 Ignition key

document_0900452a81793dcc.book Seite 114 Mittwoch, 21. März 2007 5:42 17

«
...
114
115
116
117
118
...
»

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Reviews:

No comments

Related manuals for S5 CABRIOLET

Brand: Raven Pages: 24

Brand: Weather Guard Pages: 4

Brand: HALE Pages: 44

Brand: 3SIXT Pages: 12

Brand: Alpine Pages: 2

Brand: Whispbar Pages: 15

Brand: Axxess Pages: 8

Brand: SeaSucker Pages: 9

BTFREQ PRO BTFMPD3SR

Brand: Scosche Pages: 16

2010 Civic Sedan

Brand: Honda Pages: 390

2005 P207 Explorer Sport Trac

Brand: Ford Pages: 540

Brand: v.link Pages: 21

Brand: BMW Pages: 392

Brand: Curt Manufacturing Pages: 4

Brand: Guardsman Pages: 2

Brand: Kargo Master Pages: 17

Brand: Alfa Romeo Pages: 268

Brand: Velleman Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands