Audi S5 CABRIOLET Owner'S Manual Download Page 36 | Manualshive

Page: 36 / 294

background image

Driver information system

34

WARNING

The vehicle must not be towed if there is a fault in the electronic
steering lock: the steering will be locked and the vehicle cannot be
steered. Towing a vehicle with locked steering can cause an acci-
dent.

Note

On some models the symbol may look slightly different.

Ignition lock defective



A fault in the ignition lock must be rectified immediately.

If the symbol



flashes in the display, there is a malfunc-

tion in the electronic ignition lock. The symbol is accompa-
nied by a driver message giving you more information
about the fault. This message will disappear after about
5 seconds, but you can call it up again at any time by
pressing the

button:

Ignition lock defective. Contact workshop!

– Do not switch off the engine.

– Drive the vehicle without delay to a qualified workshop

and have the fault repaired.

The ignition cannot be switched off if there is a fault in the elec-
tronic ignition lock. For this reason, you should drive the vehicle
without delay to a qualified workshop and have the cause of the
fault repaired.

If the vehicle is equipped with the advanced key* feature, you
should not switch off the engine with the Stop/Start button because
it cannot be started again after the ignition has been switched off.

Note

On some models the symbol may look slightly different.

Yellow symbols

A yellow symbol indicates a malfunction or other item
requiring attention.

Yellow symbols indicate a Priority 2 fault.

Yellow symbols are accompanied by one warning chime. The
symbol is accompanied by a driver message giving you more infor-
mation about the fault. This message will disappear after about
5 seconds, but you can call it up again at any time by pressing the

button.

The function indicated should be checked as soon as possible. The
yellow symbol will only go out when the fault has been rectified.

If several Priority 2 faults are detected at the same time, the symbols
are displayed one after the other for about 2 seconds at a time.

SET

Fig. 26 Display: Yellow
warning symbol

SET

document_0900452a81793dcc.book Seite 34 Mittwoch, 21. März 2007 5:42 17

«
...
34
35
36
37
38
...
»

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Reviews:

No comments

Related manuals for S5 CABRIOLET

Brand: Toyota Pages: 529

Brand: HALE Pages: 44

Brand: Ignition Pages: 1

Brand: Vauxhall Pages: 177

Brand: Ford Pages: 52

ESCALADE FAMILY - SPECIFICATIONS 2011

Brand: Cadillac Pages: 1

Brand: AC Schnitzer Pages: 16

Brand: NavLinkz Pages: 21

RGBW Rock Lights

Brand: Lit Lightz Pages: 3

Brand: Metra Electronics Pages: 5

Brand: Renkforce Pages: 4

Sedan CIVIC 2022

Brand: Honda Pages: 701

GMC Yukon Denali 2005

Brand: Cadillac Pages: 456

Brand: Saab Pages: 63

Brand: R&G Pages: 20

Brand: Whispbar Pages: 70

Brand: Toyota Pages: 165

Brand: Kia Pages: 680

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands