Audi S5 CABRIOLET Owner'S Manual Download Page 165 | Manualshive

Page: 165 / 294

background image

Seat belts

163

Controls

Safety

Driving tips

General maintenance

Self-help

Technical data

It is also important for the rear passengers to wear seat belts, as
they could otherwise be thrown forwards violently in an accident.
Rear passengers who do not use seat belts endanger not only them-
selves but also the other occupants

⇒

page 162, fig. 170.

How to wear seat belts properly

Putting on the three-point seat belts

Always fasten your seat belts before driving off.

– Adjust the front seat and head restraint correctly before

putting on the seat belt

⇒

page 70, “Seats and storage”.

– To fasten the belt, take hold of the latch plate and pull it

slowly across your chest and lap

⇒

.

– Insert the latch plate into the buckle for the appropriate

seat and push it down until it is securely locked with an
audible click

⇒

fig. 172.

– Pull the belt to check that it is now securely fastened.

The three-point inertia reel belts are tensioned automatically. The
retractor system gives complete freedom of movement, as long as
the pull on the belt is slow. Hard braking locks the belt. The belt will
also lock when you accelerate, drive up or down a steep hill or in a
sharp curve.

WARNING

•

Always make certain that the belt is positioned properly

⇒

fig. 171 – risk of injury

⇒

page 163, “Adjusting the seat belts”.

•

The latch plate of the belt must always be engaged in the

correct buckle for that seat. Otherwise the belt will not be fully
effective and the danger of injury increases.

Adjusting the seat belts

Always position seat belts properly for maximum safety.

Fig. 171 Positioning of
head restraints and
seat belts

Fig. 172 Driver's seat:
Belt buckle and latch
plate

Fig. 173 Adjusting
shoulder and lap belt

document_0900452a81793dcc.book Seite 163 Mittwoch, 21. März 2007 5:42 17

«
...
163
164
165
166
167
...
»

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Reviews:

No comments

Related manuals for S5 CABRIOLET

Brand: Vintage Air Pages: 28

Brand: Kia Pages: 10

Brand: Chevrolet Pages: 2

Automotive 31006

Brand: KRAFTWERK Pages: 2

Wireless Handsfree Car Kit

Brand: Wagan Pages: 20

10-8002-C11670C

Brand: Saleen Pages: 17

Brand: Actia Pages: 102

Brand: Hyundai Pages: 19

Brand: Improved Racing Pages: 17

Brand: ConWys AG Pages: 16

Brand: Broadfeet Pages: 2

Brand: v.link Pages: 19

CF-UFORCE-DRW01

Brand: FALCON RIDGE Pages: 6

Brand: Summit Racing Pages: 11

Brand: Curt Group Pages: 2

Brand: Pyle Pages: 14

Brand: CITROEN Pages: 394

Nova Electronics Hide-a-Led DEUCE DUAL HEAD W600

Brand: Ecco Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands