Audi S5 CABRIOLET Owner'S Manual Download Page 108 | Manualshive

Page: 108 / 294

background image

Heating and cooling

106

Note

When the air conditioner is operating in the cooling mode, the air is
directed mainly to outlets

and

. To ensure an adequate cooling

effect, you should not close these outlets completely.

Applies to vehicles: with deluxe automatic air conditioner plus

Air outlets for rear passengers

The air outlets for the rear cabin are located in the centre
console.

– The outlets can be opened and closed by turning the

thumbwheels.

– The direction of air delivery from these outlets can be

adjusted horizontally and vertically using the adjuster in
the centre of each outlet grille.

The flow of air from the outlets is controlled either automatically or
manually, depending on the operating mode selected. All the
outlets can provide air which is either heated, unheated, or cooled.

The heater outlets for the rear footwells are located under the front
seats.

Note

When the air conditioner is operating in the cooling mode the air is
directed mainly to the outlets in the centre console. To ensure an
adequate cooling effect, you should not close these outlets
completely.

Applies to vehicles: with deluxe automatic air conditioner plus

Economical operation of the air conditioner

Economical operation of the air conditioner will help to
save fuel.

When the air conditioner is operating in the cooling mode it
reduces engine power and increases fuel consumption. To
ensure that the cooling mode is activated only when really
necessary, please note the following points:

– Switch off the cooling mode by pressing the AC button

(LED off) if you wish to save fuel.

– You should also switch off the cooling mode by pressing

the AC button (LED off) if you open the windows or the
tilting panorama roof* while driving.

– If the vehicle has heated up after standing in the sun,

open the windows and doors for a short time to cool the
vehicle.

For the sake of the environment

By saving fuel you also reduce the amount of pollutants emitted
from your vehicle.

A

2

A

3

document_0900452a81793dcc.book Seite 106 Mittwoch, 21. März 2007 5:42 17

«
...
106
107
108
109
110
...
»

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Reviews:

No comments

Related manuals for S5 CABRIOLET

2008 MX-5 Miata

Brand: Mazda Pages: 400

Brand: STC Pages: 6

Brand: Motoalliance Pages: 8

Brand: walser Pages: 24

Brand: Harman Kardon Pages: 16

Brand: TATA Motors Pages: 184

PW-50C Civilian

Brand: B&G electronics Pages: 7

Brand: A-Tach Pages: 2

Brand: Buick Pages: 20

Brand: MULTILIFT Pages: 62

Brand: Calix group Pages: 4

Interlock 700 Series

Brand: Scania Pages: 82

Brand: Mopar Pages: 18

Brand: Lexus Pages: 82

Brand: TATA Motors Pages: 232

Brand: Safe Fleet Pages: 2

Brand: AVS Pages: 9

Brand: AA Products Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands