Audi S5 CABRIOLET Owner'S Manual Download Page 206

Page: 206 / 294

Towing a trailer

204

– Pull out the knob in direction

, hold and turn in direc-

tion

until the locking ball

engages

⇒

Inserting the ball joint

– With the spring mechanism in the “ready” position,

insert the ball joint into the mounting fixture and push it
upwards

⇒

page 203, fig. 200 in the direction indicated

(arrow)

⇒

. The spring mechanism should then

engage automatically with an audible click.

– Lock the ball joint by turning the key anti-clockwise.

– Take out the key and press the cover cap provided onto

the lock.

Continued

⇒

page 204, “Fitting the ball joint (step 4)”.

WARNING

•

If it is not possible to set the spring mechanism to the "ready"

position as described above, do not use the ball joint. Please take
your vehicle to a qualified workshop.

•

To avoid injury, keep your hands away from the knob and the

cover piece when inserting the ball joint into the mounting fixture.

Note

Make sure that the knob can turn freely when the ball joint is
inserted.

Applies to vehicles: with removable towing bracket

Fitting the ball joint (step 4)

Safety check

– Check that the green marking

⇒

fig. 201 on the knob

is inside the green zone on the ball joint.

– Check that the knob is directly against the ball joint, so

that there is no gap

between the knob and the ball

joint.

– Check that the ball joint is locked and the key is removed

(so that the knob cannot be pulled out).

Fig. 201 Removable
towing bracket: Safety
check

Fig. 202 Area below
rear bumper: Electrical
socket for trailer

document_0900452a81793dcc.book Seite 204 Mittwoch, 21. März 2007 5:42 17

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Search results

Summary of Contents for S5 CABRIOLET

Reviews:

Related manuals for S5 CABRIOLET

Brands by name

Popular brands

Audi S5 CABRIOLET, Owner'S Manual

Search results

Summary of Contents for S5 CABRIOLET

Reviews:

Related manuals for S5 CABRIOLET

Brands by name

Popular brands