manualshive.com logo in svg

Audi S5 CABRIOLET, Owner'S Manual

The Audi S5 Cabriolet's Owner's Manual is available for free download on manualshive.com. This comprehensive manual provides essential information and guidance on operating and maintaining your Audi S5 Cabriolet. Get the most out of your vehicle's features and ensure a smooth driving experience with this informative manual.

Share
Download
background image

Self-help

255

Controls

Safety

Driving tips

General maintenance

Self-help

Technical data

– Insert the hook (provided in the vehicle's tool kit) in the 

hole in the hub cap.

– Pull  off  the  hub cap 

⇒

page 251, fig. 229.

– Insert the adapter 

 completely into the wheel bolt 

.

– Fit the box spanner as far as it will go over the adapter 

.

– Loosen or tighten the wheel bolt 

⇒

page 251.

It is advisable to carry the wheel bolt adapter in the vehicle. The 
adapter is normally stored in the vehicle tool kit, underneath the 
towline anchorage. It should be put back there after use.

The code number of the anti-theft wheel bolt is stamped on the front 
of the adapter. Your Audi dealer will need this number to replace the 
adapter if lost.

Note

Note the code number of the anti-theft wheel bolt and keep it in a 
safe place – not in your vehicle.

Jump-starting

Before starting the engine

If necessary, the engine can be started by connecting it to 
the battery of another vehicle.

If the engine should ever fail to start because of a discharged 
battery, the battery can be connected to the battery of another 
vehicle to start the engine. Suitable jump leads are required.

Both batteries must be rated at 12 Volts. The capacity (Ah) of the 
booster battery should not be significantly lower than that of the 
discharged battery.

Jump leads

The jump leads must be heavy enough to carry the starter current. 
Refer to the details given by the manufacturer.

Only use jump leads with insulated battery clamps.

Positive cable – usually red

Negative cable – usually black

WARNING

•

When it is discharged the battery can freeze at temperatures 

around 0°C. A frozen battery must first be thawed out before 
connecting the jump leads, as it could otherwise explode.

•

Please note the safety warnings referring to working in the 

engine compartment 

⇒

page 221.

Note

•

There must be no contact between the two vehicles as otherwise 

current could flow as soon as the positive terminals are connected.

•

The discharged battery must be properly connected to the 

vehicle's electrical system.

•

Switch off the car telephone if necessary. Details will be given in 

the manufacturer's instructions for the car telephone.

A

2

A

1

A

2

document_0900452a81793dcc.book  Seite 255  Mittwoch, 21. März 2007  5:42 17

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Reviews:

No comments

Related manuals for S5 CABRIOLET

Parrot CK 3000 Evolution Specifications preview
CK 3000 Evolution
Brand: Parrot Pages: 2
Porsche 911 GT3R 2010 Technical Manual preview
911 GT3R 2010
Brand: Porsche Pages: 144
TBC DPI1K User Manual preview
DPI1K
Brand: TBC Pages: 12
Thule 1511 Instructions Manual preview
1511
Brand: Thule Pages: 8
CTEK D250S Dual Manual preview
D250S Dual
Brand: CTEK Pages: 84
Zap XEBRA ZAPCAR Series Owner'S Manual preview
XEBRA ZAPCAR Series
Brand: Zap Pages: 16
ICON 91824E Installation Instructions preview
91824E
Brand: ICON Pages: 4
Vauxhall Crossland X 2017 Owner'S Manual preview
Crossland X 2017
Brand: Vauxhall Pages: 245
Alfa Romeo Giulietta 2.0 JTDM Manual preview
Giulietta 2.0 JTDM
Brand: Alfa Romeo Pages: 14
Belkin F8J034 User Manual preview
F8J034
Brand: Belkin Pages: 30
Mitsubishi FTO Series Handbook preview
FTO Series
Brand: Mitsubishi Pages: 141
iSimple IS7705 Installation & Operation Manual preview
IS7705
Brand: iSimple Pages: 8
MayPole BC2085 Manual preview
BC2085
Brand: MayPole Pages: 3
Classic Accessories OVER DRIVE PolyPRO 3 Car Cover Instructions preview
OVER DRIVE PolyPRO 3 Car Cover
Brand: Classic Accessories Pages: 2
RADICAL R-C10AD2 Device Installation Manual preview
R-C10AD2
Brand: RADICAL Pages: 11
Vauxhall MasterFit Manual preview
MasterFit
Brand: Vauxhall Pages: 4
Lincoln 2012 MKX Owner'S Manual preview
2012 MKX
Brand: Lincoln Pages: 364
iDataLink BLADE-AL-HK4-EN Install Manual preview
BLADE-AL-HK4-EN
Brand: iDataLink Pages: 35

Brands by name

Popular brands

Load more brands