Audi S5 CABRIOLET Owner'S Manual Download Page 232

Page: 232 / 294

Checking and topping up fluids

230

•

Do not expose the battery to direct sunlight over a long period of

time, as the intense ultraviolet radiation can affect the battery
housing.

•

If the car is left standing for long periods, protect the battery

from extreme cold temperature so that it does not “freeze up” and
become damaged.

Charging the battery

Terminals for charging the battery are fitted in the engine
compartment.

– Note the warnings

⇒

in “Important safety warnings

for handling a car battery” on page 229 and

⇒

– Switch off all electrical equipment. Remove the ignition

key.

– Open the bonnet

⇒

page 220.

– Open the red cap on the positive terminal

⇒

fig. 217.

– Follow the correct procedure for connecting the charger

cables to the jump-start terminals (terminal with red cap
= “positive”, terminal with hexagon = “negative”).

– Now connect the battery charger to the mains and switch

on.

– After charging the battery: switch off the battery charger

and disconnect the mains cable.

– Now disconnect the charger cables.

– Refit the red cap onto the positive terminal.

– Close the bonnet

⇒

page 221.

When it is discharged the battery can freeze at temperatures
around 0°C. A frozen battery must be thawed before charging

⇒

However, it is advisable to replace the battery if it has frozen,
because the ice can crack the battery casing and allow the battery
acid to escape.

Charging the battery

Important: Before you charge the battery make sure you read the
manufacturer's instructions for using the battery charger.

When charging with a low current (for instance with a small battery
charger) the battery does not have to be disconnected. The battery
must not be opened while you are charging it.

Fast-charging the battery

For technical reasons it is not permissible to fast-charge the battery
using charging devices with an output voltage higher than 14.8 V.

WARNING

Never charge a frozen battery – it could explode.

Note

Use only the terminals in the engine compartment to charge the
battery.

Fig. 217 Engine
compartment: Termi-
nals for jump leads and
battery charger

document_0900452a81793dcc.book Seite 230 Mittwoch, 21. März 2007 5:42 17

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Search results

Summary of Contents for S5 CABRIOLET

Reviews:

Related manuals for S5 CABRIOLET

Brands by name

Popular brands

Audi S5 CABRIOLET, Owner'S Manual

Search results

Summary of Contents for S5 CABRIOLET

Reviews:

Related manuals for S5 CABRIOLET

Brands by name

Popular brands