Audi S5 CABRIOLET Owner'S Manual Download Page 167 | Manualshive

Page: 167 / 294

background image

Seat belts

165

Controls

Safety

Driving tips

General maintenance

Self-help

Technical data

– Press the red button in the seat belt buckle

⇒

page 164,

fig. 175. The latch plate will spring out of the buckle.

– Guide the belt back by hand so that it is taken up by the

retractor.

Belt tensioners

How the belt tensioners work

The seat belts for the driver and front passenger are
equipped with belt tensioners.

The seat belts on the front seats are tensioned automatically in
frontal, side and rear-end impacts above a certain degree of
severity. This helps to reduce the forward motion of the occupants.

In a less severe accident, or in the event of a roll-over, the belt
tensioners are not activated.

WARNING

•

Any work on the tensioner system or removal and installation

of system components for other repairs must be performed by a
qualified workshop.

•

The belt tensioners can only be activated once. If they have

been activated at any time, the system must be replaced.

Note

•

Some smoke may be released when the belt tensioners are acti-

vated. This does not mean there is a fire in the vehicle.

•

The relevant safety requirements must be observed when the

vehicle or components of the system are scrapped. Your authorised
Audi dealer is familiar with these regulations and will be pleased to
pass on the information to you.

document_0900452a81793dcc.book Seite 165 Mittwoch, 21. März 2007 5:42 17

«
...
165
166
167
168
169
...
»

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Reviews:

No comments

Related manuals for S5 CABRIOLET

Brand: Jeep Pages: 25

Brand: Jeep Pages: 51

Brand: Farenheit Pages: 8

Brand: Jetter Pages: 4

Brand: K&K Pages: 8

Brand: K&K Pages: 20

Brand: K&K Pages: 6

Brand: K&K Pages: 3

Brand: K&K Pages: 3

RadioPRO 5 RP5-GM41

Brand: PAC Pages: 3

Brand: RaceChip Pages: 20

Brand: Neuspeed Pages: 2

MagicWatch MWE250

Brand: Waeco Pages: 172

Brand: Yakima Pages: 9

Brand: Cadillac Pages: 402

Brand: Cobra Pages: 2

Brand: BrandMotion Pages: 6

Brand: Enduro Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands