Audi S5 CABRIOLET Owner'S Manual Download Page 269

Page: 269 / 294

Fuses and bulbs

267

Controls

Safety

Driving tips

General maintenance

Self-help

Technical data

In the case of bulb holders with a bayonet fastener please
proceed as follows:

Removing the bulb holder

– Turn the bulb holder in the direction of the arrow

⇒

page 266, fig. 245 as far as it will go and then take the

bulb holder out of the light unit.

Fitting the bulb holder

– Insert the bulb holder into the light unit, making sure you

keep the bulb holder straight, i.e. the rubber seal makes
even contact all around.

– Turn the bulb holder in the direction indicated by the

arrow

⇒

page 266, fig. 245 as far as it will go.

Changing bulbs for headlights

Removing and installing headlights

The description for removing the headlight refers to the left
headlight; in principle the same procedure applies to the
right headlight.

Removing

– Switch off the ignition and the lights.

– Open the bonnet.

– Take the screwdriver and the interchangeable Torx socket

out of the vehicle tool kit.

– Remove the screws

⇒

fig. 246 that secure the trim panel

to the lock carrier and detach the trim panel.

– Slacken the two screws that secure the headlight to the

lock carrier and the screw at the underside of the head-
light (this screw is located between the cover and the
rubber cap and should not be slackened more than ten
turns)

⇒

fig. 247.

– Carefully pull the headlight forward about 60 mm.

– Release and unplug the electrical connector.

– Carefully take the headlight out towards the front (swivel

it slightly if necessary).

Fig. 246 Trim panel:
Attachment points are
marked by arrows

Fig. 247 Headlight
unit: Attachment
points are marked by
arrows

document_0900452a81793dcc.book Seite 267 Mittwoch, 21. März 2007 5:42 17

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Search results

Summary of Contents for S5 CABRIOLET

Reviews:

Related manuals for S5 CABRIOLET

Brands by name

Popular brands

Audi S5 CABRIOLET, Owner'S Manual

Search results

Summary of Contents for S5 CABRIOLET

Reviews:

Related manuals for S5 CABRIOLET

Brands by name

Popular brands