Audi S5 CABRIOLET Owner'S Manual Download Page 49 | Manualshive

Page: 49 / 294

background image

Doors and windows

47

Controls

Safety

Driving tips

General maintenance

Self-help

Technical data

Applies to vehicles: with anti-theft alarm system

Deactivating the interior monitor and tow-
away protection

When the vehicle is locked, the alarm will be triggered if
movements are detected in the interior (e.g. by animals) or
if the vehicle's inclination is changed (e.g. during transport).
You can prevent the alarm from being triggered accidentally
by switching off the interior monitor and/or tow-away
protection.

Deactivating interior monitor

– Press switch

⇒

fig. 40. The diode in the switch will

light up.

Deactivating tow-away protection

– Press switch

. The diode in the switch will light up.

The interior monitor and tow-away protection will be switched on
again automatically the next time the vehicle is locked.

WARNING

Do not leave anyone (especially children) in the car if it is locked
from the outside and the deadlock mechanism is activated: the
doors and windows cannot then be opened from the inside.
Locked doors could delay assistance in an emergency, potentially
putting lives at risk.

Locking the passenger's door manually if the
central locking fails to work

If the central locking system should fail to work at any
time, the passenger's door will have to be locked sepa-
rately.

A mechanical locking device (only visible when the door is
open) is provided on the front passenger's door.

– Take the emergency key out of the remote control key

⇒

page 40.

– Pull the cap out of the opening

⇒

fig. 41.

– Insert the key into the slot inside and turn it to the right

as far as the stop.

Fig. 40 Front end of
the driver's door:
Swtiches for interior
monitor and tow-away
protection

A

A

A

B

Fig. 41 Door: Locking
the door manually

document_0900452a81793dcc.book Seite 47 Mittwoch, 21. März 2007 5:42 17

«
...
47
48
49
50
51
...
»

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Reviews:

No comments

Related manuals for S5 CABRIOLET

Brand: ZAPTEC Pages: 240

Brand: Saab Pages: 10

Brand: TrailFX Pages: 6

Brand: TATA Motors Pages: 236

Brand: Jeep Pages: 136

Electra 225 1965

Brand: Buick Pages: 914

PRIME DESIGN URX-001-E

Brand: Safe Fleet Pages: 8

Brand: Ranger design Pages: 24

Brand: Xingyun Pages: 74

Brand: Enduro Pages: 52

Brand: Jaeger Pages: 16

Brand: Toyota Pages: 36

Brand: Volvo Pages: 362

Brand: SSV Works Pages: 2

Brand: Seat Pages: 300

2000 Accord Sedan

Brand: Honda Pages: 320

Brand: MayPole Pages: 3

Brand: Vauxhall Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands