Audi S5 CABRIOLET Owner'S Manual Download Page 145 | Manualshive

Page: 145 / 294

background image

Audi parking system

143

Controls

Safety

Driving tips

General maintenance

Self-help

Technical data

Safety notes

Applies to vehicles: with parking system

Fault warning for the acoustic parking aid

parking system:

If you hear a long beep when you engage reverse gear, the rear
parking aid is not functioning correctly.

parking system plus*/parking system advanced*:

If you hear a long beep for a few seconds when you engage reverse
gear and the diode in the switch



* starts flashing, there is a fault

in the rear and front parking system with graphic display.

You will be notified of a system fault

•

when you manually activate the parking system via the switch



*

⇒

page 129

•

the first time you engage reverse gear after switching on the

ignition, or

•

immediately, if the fault is identified while you are using the

parking system.

Note

If the system alerts you to a fault please have the fault rectified by
an Audi workshop or other qualified workshop.

Applies to vehicles: with parking system advanced

Notes on reversing camera

We recommend that you practise parking with the reversing camera
in a quiet location (car park or similar) in order to become familiar
with the system, including the orientation lines and all the other
features. Ideally, the weather and light conditions should be good.

Vehicles or other objects shown in the MMI display appear to be
further away or closer, if:

•

you are reversing from a horizontal surface up a gradient or

down a hill,

•

you are reversing towards protruding objects,

•

the vehicle has been loaded with a greater load on the rear.

The accuracy of the orientation lines and the blue area markings
decreases if:

•

the reversing camera does not provide a reliable image, e.g. if

visibility is poor or the lens is dirty,

•

the sun is so dazzling that you cannot see the image on the

display screen.

How to clean the lens of the reversing camera:

•

Moisten the lens using a commercially available, alcohol-based

glass cleaning agent and clean the lens with a dry cloth.

•

Remove snow using a small brush.

•

If possible, use de-icing spray to remove any ice

⇒

.

WARNING

•

Even when using the reversing camera, the driver must still

keep a close watch on the area behind the vehicle and use the
mirrors.

•

For technical reasons, the reversing camera cannot show the

complete area behind the vehicle

⇒

page 135, fig. 148. It is partic-

ularly important to ensure that there are no small children or
animals near the vehicle, as the reversing camera may not always
be able to detect them (accident risk).

•

The parking aid cannot replace the full concentration of the

driver. The driver is always responsible for safety during parking
and other manoeuvres. Always keep a close watch on the area
around the vehicle.

document_0900452a81793dcc.book Seite 143 Mittwoch, 21. März 2007 5:42 17

«
...
143
144
145
146
147
...
»

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Reviews:

No comments

Related manuals for S5 CABRIOLET

Brand: UnderCover Pages: 16

Brand: Jeep Pages: 42

Brand: Jeep Pages: 44

Brand: Cadillac Pages: 20

Brand: Jeep Pages: 7

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 354

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 10

2013 Escalade ESV

Brand: Cadillac Pages: 524

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 438

Brand: Cadillac Pages: 450

2011 Escalade Hybrid

Brand: Cadillac Pages: 94

2011 Escalade Hybrid

Brand: Cadillac Pages: 94

Brand: Cadillac Pages: 78

Brand: Cadillac Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands