Audi S5 CABRIOLET Owner'S Manual Download Page 141

Page: 141 / 294

Audi parking system

139

Controls

Safety

Driving tips

General maintenance

Self-help

Technical data

parking aid are NO LONGER activated when reverse gear is engaged.
This results in the following restrictions:

parking system:

There is no distance warning.

parking system plus*:

There is no rear distance warning

⇒

page 129. However, the system

will still give a warning when obstacles are detected while driving
forwards. The graphic display

⇒

page 129, fig. 142 will switch over

to towing mode.

parking system advanced*:

There is no rear distance warning

⇒

page 131. However, the system

will still give a warning when obstacles are detected while driving
forwards. The graphic display

⇒

page 132, fig. 144 will switch over

to towing mode. The image of the reversing camera will then be
shown without orientation lines and blue area markings.

Settings

Applies to vehicles: with parking system

Adjusting warning beeps

The volume and frequency (pitch) of the beeps can be
adjusted on the sound system or MMI.

– Select: Function selector button

> Audi parking

system.

•

Rear volume - to adjust the rear volume.

•

Rear frequency - to adjust the rear frequency.

•

Front volume* - to adjust the front volume.

•

Front frequency* - to adjust the front frequency.

When you change the volume or frequency, the front or rear loud-
speaker will give a test warning beep at the new setting for about
2 seconds.

The volume and frequency settings will be automatically stored and
assigned to the remote control key.

Fig. 153 MMI display:
Selection menu

CAR

document_0900452a81793dcc.book Seite 139 Mittwoch, 21. März 2007 5:42 17

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Search results

Summary of Contents for S5 CABRIOLET

Reviews:

Related manuals for S5 CABRIOLET

Brands by name

Popular brands

Audi S5 CABRIOLET, Owner'S Manual

Search results

Summary of Contents for S5 CABRIOLET

Reviews:

Related manuals for S5 CABRIOLET

Brands by name

Popular brands