manualshive.com logo in svg

Audi S5 CABRIOLET, Owner'S Manual

The Audi S5 Cabriolet's Owner's Manual is available for free download on manualshive.com. This comprehensive manual provides essential information and guidance on operating and maintaining your Audi S5 Cabriolet. Get the most out of your vehicle's features and ensure a smooth driving experience with this informative manual.

Share
Download
background image

Instruments and warning/indicator lamps

12

Warning symbol in instrument cluster 

If the symbol 

 lights up in the display, this means that either the 

coolant temperature is too high or the coolant level is too low 

⇒

page 32.

If the needle is at the top end of the dial, this means the coolant 
temperature is too high. Stop the vehicle, switch off the engine and 
wait for it to cool down. If the warning lamp starts flashing again 
after just a short distance, contact a qualified workshop.

WARNING

•

Before opening the bonnet and checking the coolant level, 

please observe the warning information on 

⇒

page 221, “Working 

on components in the engine compartment”.

•

Never open the bonnet if you can see or hear steam or coolant 

escaping from the engine compartment; there is a risk of being 
scalded. Wait until you can no longer see or hear escaping steam 
or coolant.

Caution

•

Additional lights and other accessories in front of the air inlet 

reduce the cooling effect of the radiator. At high outside tempera-
tures and high engine loads, there is a risk of the engine over-
heating.

•

The front spoiler also ensures proper distribution of the cooling 

air when the vehicle is moving. If the spoiler is damaged this can 
reduce the cooling effect, which could cause the engine to overheat. 
You should obtain professional assistance.

Rev counter

The rev counter indicates the number of engine revolu-
tions per minute.

You should select a lower gear if the engine speed drops below 
1500 rpm. The start of the red zone on the dial indicates the 
maximum engine speed which may be used briefly when the engine 
is warm and after it has been run in properly. However, it is advisable 
to change up a gear or move the selector lever to “D” (or lift your 
foot off the accelerator) before the needle reaches the red zone.

Caution

Never allow the rev counter needle 

 

⇒

page 11, fig. 2 to go into 

the red zone on the dial for more than a very brief period: there is a 
risk of damaging the engine. The start of the red zone on the dial is 
different for some engine versions.

For the sake of the environment

Changing up a gear early will help you to save fuel and minimise 
engine noise.

 button

This button has a number of different functions.

A

2

SET

Fig. 3  Instrument 
cluster: SET button

document_0900452a81793dcc.book  Seite 12  Mittwoch, 21. März 2007  5:42 17

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Reviews:

No comments

Related manuals for S5 CABRIOLET

GMC HUMMER EV 2022 Manual preview
HUMMER EV 2022
Brand: GMC Pages: 140
Accel 2020 Installation Instructions preview
2020
Brand: Accel Pages: 2
Mazda 2012 Mazda6 Owner'S Manual preview
2012 Mazda6
Brand: Mazda Pages: 527
Cadillac 2008 Escalade EXT Owner'S Manual preview
2008 Escalade EXT
Brand: Cadillac Pages: 496
Pyle PLCMRV8B Black User Manual preview
PLCMRV8B Black
Brand: Pyle Pages: 4
Honda Pilot 2019 Owner'S Manual preview
Pilot 2019
Brand: Honda Pages: 85
Honda 2010 Pilot Technology Reference Manual preview
2010 Pilot
Brand: Honda Pages: 20
Kia 2009 Rio Series Owner'S Manual preview
2009 Rio Series
Brand: Kia Pages: 219
Opel 2013 Corsa Brochure & Specs preview
2013 Corsa
Brand: Opel Pages: 32
r.LiNK RL2-NBT Manual preview
RL2-NBT
Brand: r.LiNK Pages: 20
Pontiac 2006 Relay Getting To Know Manual preview
2006 Relay
Brand: Pontiac Pages: 20
Enduro EM203 User Manual preview
EM203
Brand: Enduro Pages: 52
Billien OBU 5050 Quick Installation Manual preview
OBU 5050
Brand: Billien Pages: 2
Lexus ES 2021 Quick Manual preview
ES 2021
Brand: Lexus Pages: 28
newmotion Dynamic Power Management Home - Module Installation Instruction preview
Dynamic Power Management Home - Module
Brand: newmotion Pages: 20
Brodit Getac T800 Quick Start Manual preview
Getac T800
Brand: Brodit Pages: 2
Saturn 2009 OUTLOOK Owner'S Manual preview
2009 OUTLOOK
Brand: Saturn Pages: 432
Chevrolet Chevy II 1965 Owner'S Manual preview
Chevy II 1965
Brand: Chevrolet Pages: 46

Brands by name

Popular brands

Load more brands