Audi S5 CABRIOLET Owner'S Manual Download Page 142

Page: 142 / 294

Audi parking system

140

Applies to vehicles: with parking system plus

Switching graphic display on and off

The settings for the graphic display can be selected on the
sound system or MMI.

– Select: Function selector button

> Audi parking

system > Display.

If you have selected Graphic in the settings, the screen

⇒

page 140,

fig. 156 will automatically show the graphic display when the
parking system is activated.

Note

If you change the settings on the sound system or MMI, the changes
will not take effect until the next time you switch on the parking
system.

Applies to vehicles: with parking system advanced

Switching graphic display/reversing camera
on and off

The settings for the graphic display and reversing camera
can be selected on the sound system or MMI.

– Select: Function selector button

> Audi parking

system > Display

⇒

fig. 155.

When parking, you can use the reversing camera (Rear View) and
the graphic display separately or in combination.

If you manually switch over to the reversing camera by pressing the
control button marked Rear View

⇒

fig. 156 the control button in

the bottom right-hand corner will show Graphic

⇒

page 137,

Fig. 154 MMI display:
Display APS - submenu

CAR

Fig. 155 MMI display:
Display APS - submenu

Fig. 156 MMI display:
proximity graphic

CAR

document_0900452a81793dcc.book Seite 140 Mittwoch, 21. März 2007 5:42 17

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Search results

Summary of Contents for S5 CABRIOLET

Reviews:

Related manuals for S5 CABRIOLET

Brands by name

Popular brands

Audi S5 CABRIOLET, Owner'S Manual

Search results

Summary of Contents for S5 CABRIOLET

Reviews:

Related manuals for S5 CABRIOLET

Brands by name

Popular brands