Audi S5 CABRIOLET Owner'S Manual Download Page 107 | Manualshive

Page: 107 / 294

background image

Heating and cooling

105

Controls

Safety

Driving tips

General maintenance

Self-help

Technical data

remain on until the ignition is switched off. When the rear window
heating is switched on, this setting will remain activated for 15
minutes after switching off the ignition.

If the engine is started again during this period of 15 minutes, the
rear window heating will be switched on for about 10 to 20 minutes,
depending on the exterior temperature. This means you do not have
to manually switch on the rear window heating again if the vehicle
has only been parked for a short time.

For the sake of the environment

Switch off the heated rear window manually as soon as the rear
window is clear. By saving electrical power you can also save fuel.

Applies to vehicles: with deluxe automatic air conditioner plus

AC mode

Deactivating the AC mode

– Press the

button.

Activating the AC mode

– Press the

button again.

In the AC mode, the air cooling system is switched on and the
heating and ventilation are regulated automatically.

Note

If the LED in the AC button should continue to light up when the AC
mode has been switched off (i.e. the air conditioner has been
switched off) this is due to a defect in one of the air conditioner
components. If a malfunction should occur, please contact a quali-
fied workshop.

Applies to vehicles: with deluxe automatic air conditioner plus

Air outlets

The air distribution setting directs the air to the outlets
you select.

Fig. 120 Dashboard: Location of air outlets

Air outlets

and

– The outlets can be opened and closed by turning the

thumbwheels next to them.

– The direction of air delivery from these outlets can be

adjusted horizontally and vertically using the adjuster in
the centre of each outlet grille.

The flow of air from the outlets is controlled either automatically or
manually, depending on the operating mode selected. Outlets

to

can provide air which is either heated, unheated, or cooled.

AC

AC

AC

A

2

A

3

A

1

A

4

document_0900452a81793dcc.book Seite 105 Mittwoch, 21. März 2007 5:42 17

«
...
105
106
107
108
109
...
»

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Reviews:

No comments

Related manuals for S5 CABRIOLET

Brand: Baja Designs Pages: 6

Brand: NavLinkz Pages: 4

Brand: GMC Pages: 425

Brand: Audi Pages: 9

Brand: Belkin Pages: 4

Brand: STC Pages: 6

PRIME DESIGN HXR-269-E-UM3-80

Brand: Safe Fleet Pages: 12

Brand: Conrad Pages: 50

Brand: Honda Pages: 4

Brand: Pet Gear Pages: 4

Brand: Westin Pages: 3

Brand: Brodit Pages: 2

Brand: Ultraplast Pages: 5

Brand: Yakima Pages: 10

Brand: Menabo Pages: 4

Brand: AutoMaxi Pages: 2

Brand: CDI Pages: 2

Mini CAM-MB7-AD

Brand: Adaptiv Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands