manualshive.com logo in svg

Audi S5 CABRIOLET, Owner'S Manual

The Audi S5 Cabriolet's Owner's Manual is available for free download on manualshive.com. This comprehensive manual provides essential information and guidance on operating and maintaining your Audi S5 Cabriolet. Get the most out of your vehicle's features and ensure a smooth driving experience with this informative manual.

Share
Download
background image

General notes

280

Vehicle data sticker

The vehicle data sticker 

⇒

page 279, fig. 264 is located near the 

battery in the luggage compartment. One section of the vehicle data 
sticker is attached to the inside cover of the Service Schedule before 
the vehicle is handed over.

The sticker lists the following data:

Vehicle identification number (chassis number)

Vehicle type / engine power / gearbox type

Engine and gearbox code letters

Paint No. / Interior equipment No.

Optional equipment codes

Fuel consumption and emissions

Fuel consumption and emissions

Information on the vehicle's fuel consumption and emissions is 
given at the bottom of the vehicle data sticker 

:

Urban cycle consumption (ltr./100 km)

Extra-urban cycle consumption (ltr./100 km)

Combined cycle consumption (ltr./100 km)

Combined CO

2

 emissions (g/km)

The specified values were determined in accordance with the test 
procedure prescribed by the currently applicable version of 
Directive 80/1268/EEC. The specifications do not refer to an indi-
vidual vehicle. The consumption figures achieved during normal 
driving may differ from the test values quoted in accordance with 
the above Directive, depending on special equipment fitted, vehicle 
loading, personal driving style, road and traffic conditions, environ-
mental factors and the condition of the car.

A

1

A

2

A

3

A

4

A

5

A

6

A

6

A

A

A

B

A

C

A

D

document_0900452a81793dcc.book  Seite 280  Mittwoch, 21. März 2007  5:42 17

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Reviews:

No comments

Related manuals for S5 CABRIOLET

Kargo Master 40640 Assembly Manual preview
40640
Brand: Kargo Master Pages: 5
Falcon 1990 Installation Instructions And Specifications preview
1990
Brand: Falcon Pages: 8
Alpine eX-10 Owner'S Manual preview
eX-10
Brand: Alpine Pages: 69
Allen Sports S302 Instructions preview
S302
Brand: Allen Sports Pages: 2
Doug Thorley Headers THY-464-1 Instructions preview
THY-464-1
Brand: Doug Thorley Headers Pages: 5
Edelbrock 66002 Installation Instructions preview
66002
Brand: Edelbrock Pages: 2
EUFAB 11556 Operating Instructions Manual preview
11556
Brand: EUFAB Pages: 52
M7 SPEED AGS-R2 Manual preview
AGS-R2
Brand: M7 SPEED Pages: 6
ULTIMATE SPEED 279746 Assembly And Safety Advice preview
279746
Brand: ULTIMATE SPEED Pages: 6
travall TDG-1301 Fitting Instruction preview
TDG-1301
Brand: travall Pages: 2
Gacell 13553 User Manual preview
13553
Brand: Gacell Pages: 12
E&G Classics 1398-0502-09 Instruction Manual preview
1398-0502-09
Brand: E&G Classics Pages: 2
Subaru Legacy 2011 Quick Reference Manual preview
Legacy 2011
Brand: Subaru Pages: 19
Weltmann KFZ-Teile 9B500016 Fitting Instructions Manual preview
9B500016
Brand: Weltmann KFZ-Teile Pages: 12
MAcarbon MAA.R8.06 Install Instructions preview
MAA.R8.06
Brand: MAcarbon Pages: 3
Honda 2009 S2000 Owner'S Manual preview
2009 S2000
Brand: Honda Pages: 268
PUTCO 1951 Series Instruction Manual preview
1951 Series
Brand: PUTCO Pages: 3
Oldsmobile 1994 88 Owner'S Manual preview
1994 88
Brand: Oldsmobile Pages: 276

Brands by name

Popular brands

Load more brands