manualshive.com logo in svg

Audi S5 CABRIOLET, Owner'S Manual

The Audi S5 Cabriolet's Owner's Manual is available for free download on manualshive.com. This comprehensive manual provides essential information and guidance on operating and maintaining your Audi S5 Cabriolet. Get the most out of your vehicle's features and ensure a smooth driving experience with this informative manual.

Share
Download
background image

Self-help

254

– Screw in the mounting pin (provided in the vehicle's tool 

kit) by hand in place of the wheel bolt 

⇒

page 253, 

fig. 234.

– Then unscrew the other wheel bolts as described above.

– Take off the wheel. The mounting pin stays where it is.

Putting on the spare wheel

– Put on the spare wheel, using the mounting pin to guide 

it into place.

– Screw in the wheel bolts and tighten them lightly using 

the hexagonal opening in the screwdriver handle.

– Then unscrew the mounting pin and tighten the 

remaining wheel bolt lightly.

– Carry out the steps required after you have changed the 

wheel 

⇒

page 251, “After changing a wheel”.

The wheel bolts should be clean and turn easily. Before putting on 
the spare wheel, inspect the condition of the wheel and hub 
mounting surfaces. These surfaces must be clean before mounting 
the wheel.

The wheel bolts are easier to remove from the wheel rim if you use 
the hexagonal socket in the screwdriver handle. The reversible 
screwdriver blade should be removed as a precautionary measure 
when the tool is used for this purpose.

Note the direction of rotation when putting on a tyre with direc-
tional tread pattern 

⇒

page 254.

Note

Do not use the hexagonal socket in the screwdriver handle to loosen 
or tighten the wheel bolts.

Tyres with directional tread pattern

Tyres with directional tread pattern must be mounted so 
that they rotate in the correct direction.

A directional tread pattern is identified by arrows on the sidewall 
pointing in the forward running direction. Always note the direction 
of rotation indicated when mounting the wheel. This is important so 
that these tyres can give maximum grip and avoid excessive noise, 
tread wear and aquaplaning.

Drive carefully should you ever have a puncture and have to mount 
the spare wheel so it rotates in the wrong direction. This is because 
the tyre will not give optimum performance. Bear this in mind 
particularly when driving on wet roads.

To benefit from the advantages of tyres with this type of tread 
pattern, the defective tyre should be replaced and refitted as soon 
as possible so that all tyres again rotate in the correct direction.

Applies to vehicles: with anti-theft wheel bolts

Anti-theft wheel bolts

A special adapter is required to turn the anti-theft wheel 
bolts.

Fig. 235  Anti-theft 
wheel bolt with 
adapter

document_0900452a81793dcc.book  Seite 254  Mittwoch, 21. März 2007  5:42 17

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Reviews:

No comments

Related manuals for S5 CABRIOLET

Prorack K383 Fitting Instructions Manual preview
K383
Brand: Prorack Pages: 14
FVC Sprinter Bed System Adventure Wagon Kit Installation Manual preview
Sprinter Bed System Adventure Wagon Kit
Brand: FVC Pages: 8
Roadmaster Sterling ALL-TERRAIN 576 Owner'S Manual & Installation Instructions preview
Sterling ALL-TERRAIN 576
Brand: Roadmaster Pages: 12
PEUGEOT 407 2010 Manual preview
407 2010
Brand: PEUGEOT Pages: 249
Ranger design 1506-PHX Cargo Plus Installation Manual preview
1506-PHX Cargo Plus
Brand: Ranger design Pages: 8
AUTOTECH 10.411.01.219K Installation Instructions preview
10.411.01.219K
Brand: AUTOTECH Pages: 1
RBO RBO4038 Product Manual preview
RBO4038
Brand: RBO Pages: 15
Magneti Marelli 350203061230 Installation Instruction preview
350203061230
Brand: Magneti Marelli Pages: 2
APS IA06SJD4B Installation Instructions preview
IA06SJD4B
Brand: APS Pages: 3
Kia Picanto Manual preview
Picanto
Brand: Kia Pages: 680
Prorack K663 Fitting Instructions Manual preview
K663
Brand: Prorack Pages: 15
Jeep Grand Cherokee SRT 2019 Owner'S Manual preview
Grand Cherokee SRT 2019
Brand: Jeep Pages: 656
Roadmaster 195125 Assembly And Operating Instructions preview
195125
Brand: Roadmaster Pages: 4
Soundoff Signal nERGY ETSA200R-PA Quick Start Manual preview
nERGY ETSA200R-PA
Brand: Soundoff Signal Pages: 3
Truma Mover H SE User Manual preview
Mover H SE
Brand: Truma Pages: 10
Butts of Bawtry TBT4700 Quick Start Manual preview
TBT4700
Brand: Butts of Bawtry Pages: 2
Belkin LineCast Auto FM User Manual preview
LineCast Auto FM
Brand: Belkin Pages: 15
Rover 75 Saloon Owner'S Handbook Manual preview
75 Saloon
Brand: Rover Pages: 285

Brands by name

Popular brands

Load more brands