Audi S5 CABRIOLET Owner'S Manual Download Page 33 | Manualshive

Page: 33 / 294

background image

Driver information system

31

Controls

Safety

Driving tips

General maintenance

Self-help

Technical data

– Switch off the engine.

– Check the function displayed. Obtain professional assist-

ance if necessary.

The red symbols indicate a Priority 1 fault (serious malfunction).

Should a Priority 1 fault occur, a red warning symbol will appear at
the top of the display

⇒

page 30, fig. 25. The symbol is accompa-

nied by a driver message giving you more information about the
fault. This symbol is accompanied by three warning chimes. The
symbol will keep flashing until the fault is corrected.

If several Priority 1 faults are detected at the same time, the symbols
are displayed one after the other for about 2 seconds at a time.

This message will disappear after about 5 seconds, but you can call
it up again at any time by pressing the

button

⇒

page 30.

Alternator fault



If the symbol



flashes in the instrument cluster display, there is an

alternator fault or a fault in the vehicle's electrical system. In addi-
tion, a message will appear. This message will disappear after about

5 seconds, but you can call it up again at any time by pressing the

button.

You should normally be able to drive to the next available qualified
workshop. However, you should avoid using electrical equipment
that is not absolutely necessary because this will drain the battery.

Caution

If the coolant warning lamp



in the instrument display lights up

as well as the alternator warning lamp while driving

⇒

page 32, stop

the vehicle immediately and switch off the engine. In this case the
coolant pump is no longer being driven, and there is a risk of engine
damage.

Fault in the brake system



A fault in the brake system should be corrected as soon as
possible.

If the symbol



flashes in the display, there is a fault in the

brake system. The symbol is accompanied by a driver
message giving you more information about the fault. This
message will disappear after about 5 seconds, but you can
call it up again at any time by pressing the

button:

Stop vehicle and check brake fluid level

– Stop the vehicle.

– Check the brake fluid level

⇒

page 227.

– Obtain professional assistance if necessary.

Warning! Fault in ABS brake system. Contact
workshop

– Drive carefully to the nearest qualified workshop and

have the fault rectified

⇒

.



Alternator fault

⇒

page 31



Fault in brake system/ parking
brake

⇒

page 31



Coolant level too low / coolant
temperature too high

⇒

page 32



Engine oil pressure too low

⇒

page 33



Fault in the steering system

⇒

page 33



Ignition lock defective

⇒

page 34

SET

SET

SET

document_0900452a81793dcc.book Seite 31 Mittwoch, 21. März 2007 5:42 17

«
...
31
32
33
34
35
...
»

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Reviews:

No comments

Related manuals for S5 CABRIOLET

Brand: AA Products Pages: 6

Brand: Allen Sports Pages: 2

Brand: Ford Pages: 2

Brand: Würth Pages: 36

Brand: Chevrolet Pages: 412

Brand: Easee Pages: 12

Brand: Subaru Pages: 298

Brand: Master Tailgaters Pages: 10

BLADE-AL-HK4-EN

Brand: iDataLink Pages: 35

Brand: Prorack Pages: 14

Brand: SEC Pages: 2

Brand: Volkswagen Pages: 2

Brand: SAF-HOLLAND Pages: 22

2003 TraiIBIazer

Brand: Chevrolet Pages: 426

2003 S10 Pickup

Brand: Chevrolet Pages: 434

Actyon Sports II 2012.01

Brand: SSANGYONG Pages: 719

Brand: Lakewood Pages: 4

2013 Corsa Infotainment system

Brand: Vauxhall Pages: 227

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands