Audi S5 CABRIOLET Owner'S Manual Download Page 23 | Manualshive

Page: 23 / 294

background image

Driver information system

21

Controls

Safety

Driving tips

General maintenance

Self-help

Technical data

CD and radio display

If no priority 1 or 2 faults have been detected by the auto-check
control, the name or frequency of the current radio station and the
selected waveband will appear the upper part of the display.

When a CD is playing, the display will show the current title. If the
vehicle is equipped with a CD changer* the display will also show
the number of the CD being played (CD1 to CD6).

Outside temperature display

The outside temperature is shown when the display is
activated.

At temperatures below +5°C a snowflake symbol appears next to the
temperature display. This is to warn the driver to take extra care
when there is a risk of ice on the road.

When the vehicle is stationary or travelling at very low speeds, the
temperature displayed may be slightly higher than the actual
outside temperature as a result of the heat radiated from the
engine.

The temperature units can be set to °F or °C on the MMI* or sound
system control console. The outside temperature is automatically
displayed in the units you have selected. Please refer to the Oper-
ating Manual for the MMI* or sound system.

WARNING

Do not rely on the outside temperature display as an ice warning.
Please bear in mind that there may be patches of ice on the roads
even at outside temperatures 5°C.

Applies to vehicles: with manual gearbox and gear-change indicator

Gear-change indicator

This additional indicator function can help to save fuel.

Fig. 9 Display: Radio
information

Fig. 10 Display:
Outside temperature

Fig. 11 Display: Gear-
change indicator

document_0900452a81793dcc.book Seite 21 Mittwoch, 21. März 2007 5:42 17

«
...
21
22
23
24
25
...
»

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Reviews:

No comments

Related manuals for S5 CABRIOLET

Brand: Daihatsu Pages: 1718

Brand: AA Products Pages: 6

Brand: A-Tach Mounts Pages: 2

Brand: Toyota Pages: 35

Brand: AMP Research Pages: 12

Half Size Trunk Box Organizer C-TBO-CV

Brand: Havis-Shields Pages: 1

Brand: Volvo Pages: 8

Brand: SnapPad Pages: 5

Brand: Cadillac Pages: 407

Brand: GROM Audio Pages: 20

Brand: Acura Pages: 347

Turbocharger 15012

Brand: Edelbrock Pages: 1

Yukon XL Denali 2015

Brand: GMC Pages: 439

OVER DRIVE PolyPRO 3 Car Cover

Brand: Classic Accessories Pages: 2

Brand: Magneti Marelli Pages: 2

Brand: Istar Pages: 6

Brand: Yakima Pages: 9

Brand: Prorack Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands