Audi S5 CABRIOLET Owner'S Manual Download Page 249 | Manualshive

Page: 249 / 294

background image

Self-help

247

Controls

Safety

Driving tips

General maintenance

Self-help

Technical data

How to use the compact temporary spare wheel

Should you ever have a punctured tyre, the compact temporary
spare wheel is only intended for temporary use until you can reach
a workshop. The standard-size road wheel should be refitted as
soon as possible.

Please note the following restrictions when using the compact
temporary spare wheel. The compact temporary spare wheel is
designed specifically for this model. For this reason, do not use a
temporary spare from a different type of vehicle.

Snow chains

For technical reasons, snow chains must not be used on the
compact temporary spare wheel.

If you should have a puncture on one of the front wheels when using
snow chains, fit the compact temporary spare in place of one of the
rear wheels. You can then attach the snow chains to the wheel taken
from the rear and use this wheel to replace the punctured front
wheel.

WARNING

•

The tyre pressures must be checked and corrected as soon as

possible. The tyre pressure of the compact temporary spare wheel
must be 4.2 bar – an incorrectly inflated tyre can cause an acci-
dent.

•

Do not drive faster than 80 km/h - higher speeds can cause an

accident.

•

Avoid heavy acceleration, hard braking and fast cornering – risk

of accident.

•

Never use two or more compact spare tyres at the same time –

risk of accident.

•

No other type of tyre (normal summer or winter tyres) may be

fitted on the compact temporary spare wheel.

Tyre repairs

General information and safety notes

Repaired tyres are only suitable for temporary use.

Your vehicle is equipped with a tyre repair kit: the Tyre Mobility
System (TMS).

In the event of a puncture you will find the TMS, which consists of a
sealing compound and a compressor, located under the floor panel
in the luggage compartment.

The TMS will reliably seal tyres damaged by foreign bodies,
provided that the cuts or punctures are no larger than approx. 4 mm
in diameter.

It is not necessary to remove the foreign body from the tyre.

The sealing compound must not be used:

•

on cuts and punctures larger than 4 mm

⇒

fig. 227

•

if the wheel rim has been damaged

•

if you have been driving with very low pressure or a completely

flat tyre

.

How to use the TMS is described in the section Repairing a tyre

⇒

page 248 and in the instructions supplied with the tyre sealant

can.

Fig. 227 The Tyre
Mobility System is NOT
suitable for repairing
this type of damage to
tyres.

A

1

A

2

A

3

document_0900452a81793dcc.book Seite 247 Mittwoch, 21. März 2007 5:42 17

«
...
247
248
249
250
251
...
»

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Reviews:

No comments

Related manuals for S5 CABRIOLET

Brand: Abarth Pages: 176

Brand: GMC Pages: 425

Brand: Gator Pages: 8

Brand: P-Invent Pages: 4

Brand: EUFAB Pages: 16

Brand: Pacbrake Pages: 6

Brand: Reese Explore Pages: 9

Brand: Saab Pages: 92

Brand: A-rival Pages: 23

Brand: AIS Pages: 2

RearSight 250-8308

Brand: Rostra Pages: 2

2003 Silhouette

Brand: Oldsmobile Pages: 466

K40 Platinum360

Brand: K40 ELECTRONICS Pages: 11

Brand: Classic AutoAir Pages: 44

Brand: Aston Martin Pages: 415

Brand: Porsche Pages: 146

Brand: BMW Pages: 64

Platinum Pro Plug-in

Brand: Haltech Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands