Audi S5 CABRIOLET Owner'S Manual Download Page 122 | Manualshive

Page: 122 / 294

background image

Driving

120

Note

•

The parking brake can be applied at any time - even when the

ignition is switched off. However, the ignition must be switched on
before the parking brake can be released.

•

Any slight noise which may be heard when the parking brake is

applied or released is quite normal and no cause for concern.

•

The parking brake runs an automatic test cycle at regular inter-

vals when the vehicle is parked. This may also cause a slight noise,
which is normal.

Parking

Please note the following points to ensure there is no risk
of the car rolling away accidentally after it is parked.

Parking the car

– Use the foot brake to stop the vehicle.

– Pull the switch to apply the parking brake.

– Automatic gearbox: Move the selector lever to P.

– Switch off the engine

⇒

.

– Manual gearbox: Engage the first gear.

When parking on slopes

– Turn the steering wheel so that the vehicle would roll into

the kerb if it did start to move accidentally.

WARNING

•

Always take the key with you when leaving the vehicle – even

if you only intend to be gone for a short time. This is especially
important if children are left in the car. They might otherwise be
able to start the engine, release the parking brake or use power-

operated equipment such as the electric windows - this could lead
to injuries.

•

Do not leave anyone (especially children) in the vehicle when it

is locked. Locked doors could delay assistance in an emergency,
potentially putting lives at risk.

Driving away from a standstill

The parking brake auto release function releases the
parking brake automatically when you wish to start
moving.

Applying the parking brake when stopping

– Pull the switch to apply the parking brake.

Releasing the parking brake when driving away

– Drive off in the normal way: the parking brake will be

released automatically and the vehicle will start moving.

On vehicles with automatic gearbox, you can apply the parking
brake when stopping at traffic lights, etc. Then you do not have to
hold the car with the footbrake, as the parking brake will stop it
creeping forward while a gear is engaged in the automatic transmis-
sion. When you drive off in the normal way, the parking brake will be
released automatically and the vehicle will start moving.

Driving away on a slope

When driving away on a gradient, the parking brake auto release
function prevents the vehicle from rolling back unintentionally. The
braking force of the parking brake is only released when there is
enough power at the wheels to make the vehicle move in the desired
direction.

WARNING (continued)

document_0900452a81793dcc.book Seite 120 Mittwoch, 21. März 2007 5:42 17

«
...
120
121
122
123
124
...
»

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Reviews:

No comments

Related manuals for S5 CABRIOLET

Brand: kaarta Pages: 29

Brand: FormFit Pages: 2

Car Top Duffle Bag

Brand: Rightline Gear Pages: 2

Escalade ESV 2014

Brand: Cadillac Pages: 508

Brand: Hama Pages: 2

Xplore Pro II SxS

Brand: Marlon Pages: 15

Brand: Jeep Pages: 380

Brand: Flash Cover Pages: 2

Brand: Porsche Pages: 98

Brand: Softride Pages: 4

Brand: Tesla Pages: 274

Brand: INDIWORK Pages: 18

Brand: Opel Pages: 103

Brand: Needit Pages: 2

KIT ParkingSensor 814

Brand: Gemini Pages: 6

Brand: Mopar Pages: 18

Brand: Yakima Pages: 28

Brand: Rydeen Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands