Audi S5 CABRIOLET Owner'S Manual Download Page 274

Page: 274 / 294

Fuses and bulbs

272

Changing bulbs in boot lid

Rear lights in boot lid

•

Rear fog light

•

Reversing light

Before you begin working, please make yourself familiar with the
different bulb versions

⇒

page 265.

Removing bulb carrier

The description for changing the bulb refers to the left rear
light unit; in principle the same procedure applies to the
right rear light unit.

– Check which of the bulbs is defective.

– Open the boot lid.

– Take the screwdriver out of the vehicle tool kit.

– Using the flat-blade side of the reversible screwdriver

insert, carefully detach the cover cap

⇒

fig. 257 -arrows-.

– Using the screwdriver, unscrew the nut

⇒

fig. 258

the anti-clockwise direction and remove the nut and the
retaining clip

– Release the retaining tab

and remove the bulb holder

from the light unit.

– Change the bulb

⇒

page 273.

Fig. 256 Rear lights in
boot lid

Fig. 257 Boot lid:
Opening the cover in
the boot lid

Fig. 258 Boot lid:
Removing bulb carrier

document_0900452a81793dcc.book Seite 272 Mittwoch, 21. März 2007 5:42 17

Summary of Contents for S5 CABRIOLET







































































































































































































































































































Search results

Summary of Contents for S5 CABRIOLET

Reviews:

Related manuals for S5 CABRIOLET

Brands by name

Popular brands

Audi S5 CABRIOLET, Owner'S Manual

Search results

Summary of Contents for S5 CABRIOLET

Reviews:

Related manuals for S5 CABRIOLET

Brands by name

Popular brands