manualshive.com logo in svg

ARTERY AT32F435 Series, Reference Manual

Share
Download
ARTERY AT32F435 Series Reference Manual Download Page 694

  AT32F435/437

 

Series  Reference  Manual

 

2022.11.11

 

Page 694 

 

Rev 2.03

 

Bit 15 

PINCOS 

00x 

rw 

Peripheral increase offset 
0: Peripheral increase offset disabled 
1: Peripheral increase offset enabled 
If PINCOS bit is enabled, the offset size of the peripheral 
address  calculation  is  fixed  to  32-bit  alignment.  This  bit 
has no meaning if PINCM=0. 
This bit is forced low by hardware when the direction mode 
is selected or if PBURST is different from 00. 
This bit can be written only when SEN=0. 

Bit 14

: 13  MWIDTH 

0x0 

rw 

Memory data width 
This  field  defines  the  HSIZE  (AHB  bus  signal)  in  the 
memory controller. 
00: Byte (8-bit) 
01: Half-word (16-bit) 
10: Word (32-bit) 
11: Reserved 
In direct mode, this field is forced by hardware to be same 
value as PWIDTH when SEN=1. 
This field can be written only when SEN=0. 

Bit 12

: 11  PWIDTH 

00x 

rw 

peripheral data width 
This  field  defines  the  HSIZE  (AHB  bus  signal)  in  the 
peripheral controller. 
00: Byte (8-bit) 
01: Half-word (16-bit) 
10: Word (32-bit) 
11: Reserved 
This field can be written only when SEN=0. 

Bit 10 

MINCM 

0x0 

rw 

Memory increment mode 
0: Memory address pointer is fixed 
1: Memory address pointer is incremented 
This bit can be written only when SEN=0. 

Bit 9 

PINCM 

0x0 

rw 

peripheral increment mode 
0: Peripheral address pointer is fixed 
1: Peripheral address pointer is incremented 
This bit can be written only when SEN=0. 

Bit 8 

LM 

0x0 

rw 

Loop mode 
0: Loop mode is disabled 
1: Loop mode is enabled 
This bit is forced flow by hardware if PFCTRL=1, as soon 
as SEN=1. 
This bit is forced high by hardware if DMM=1, as soon as 
SEN=1. 

Bit 7

: 6 

DTD 

0x0 

rw 

data transfer direction 
00: Peripheral to memory (P2M) 
01: Memory to peripheral (M2P) 
10: Memory to memory (M2M) 
11: Reserved 
This bit can be written only when SEN=0. 

Bit 5 

PFCTRL 

0x0 

rw 

Peripheral flow controller 
0: DMA is the flow controller 
1: The peripheral is the flow controller 
This bit is forced low by hardware if DTD=10 (M2M). 
This bit can be written only when SEN=0. 

Bit 4 

FDTIEN 

0x0 

rw 

Full data transfer interrupt enable 
0: TC interrupt disabled 
1: TC interrupt enabled 

Bit 3 

HDTIEN 

0x0 

rw 

Half data transfer interrupt enable 
0: HT interrupt disabled 
1: HT interrupt enabled 

Summary of Contents for AT32F435 Series





































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands