manualshive.com logo in svg

ARTERY AT32F435 Series, Reference Manual

Share
Download
ARTERY AT32F435 Series Reference Manual Download Page 632

  AT32F435/437

 

Series  Reference  Manual

 

2022.11.11

 

Page 632 

 

Rev 2.03

 

significant byte bit [7: 0] is read. 

Bit 1 

SCR 

0x0 

rw 

Stop Counter Rollover 
When this bit is set, the counter does not roll over to 0 after 
it reaches the maximum value. 

Bit 0 

RC 

0x0 

rw 

Reset Counter 
When  this  bit  is  set,  all  counters  are  reset.  This  bit  is 
cleared automatically after 1 clock cycle. 

26.3.35 Ethernet MMC receive interrupt register (EMAC_MMCRI)  

The EMAC_MMCRI register contains the interrupts generated in the following conditions: 

 

Receive statistic counters reaches half their maximum values (32-bit counter corresponds to 
0x8000_0000, and 16-bit counter corresponds to 0x8000) 

 

Receive statistic counters exceed their maximum values (32-bit counter corresponds to 
0xFFFF_FFFF, and 16-bit counter corresponds to 0xFFFF) 

When the counter stops rolling, an interrupt is set but the counter is still all 1. The EMAC_MMCRI is a 
32-bit register. An interrupt bit is cleared when the MMC counter that generates the interrupt is read. 
The least  significant  byte  bit  [7:  0]  of  the  corresponding  counter must  be  read  in order  to  clear  the 
interrupt bit. 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 18  Reserved 

0x0000 

resd 

Kept at its default value. 

Bit 17 

RGUF 

0x0 

rrc 

Received Good Unicast Frames 
This  bit  is  set  when  the  received  good  unicast  frame 
counter reaches the maximum value or half the maximum 
value. 

Bit 16: 7 

Reserved 

0x000 

resd 

Kept at its default value. 

Bit 6 

RFAE 

0x0 

rrc 

Received Frames Alignment Error 
This  bit  is  set  when  the  received  frame  counter  with 
alignment  error  reaches  the  maximum  value  or  half  the 
maximum value.   

Bit 5 

RFCE 

0x0 

rrc 

Received Frames CRC Error 
This  bit  is  set  when  the  receive  frame  with  CRC  error 
reaches the maximum value or half the maximum value. 

Bit 4: 0 

Reserved 

0x00 

resd 

Kept at its default value. 

26.3.36 Ethernet MMC transmit interrupt register (EMAC_MMCTI)  

The  EMAC_MMCTI  register  contains  the  interrupts  generated  in  the  following  conditions:  when  the 
transmit statistic counters reach half their maximum values (32-bit counter corresponds to 0x8000_0000, 
and  16-bit  counter  corresponds  to  0x8000),  and  when  the  transmit  statistic  counters  exceed  their 
maximum  values  (32-bit  counter  corresponds  to  0xFFFF_FFFF,  and  16-bit  counter  corresponds  to 
0xFFFF).  When  the  counter  stops  rolling,  an  interrupt  is  set  but  the  counter  is  still  all  1.  The 
EMAC_MMCTI is a 32-bit register. An interrupt bit is cleared when the MMC counter that generates the 
interrupt is read. The least significant byte bit [7: 0] of the corresponding counter must be read in order 
to clear the interrupt bit. 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 22  Reserved 

0x000 

resd 

Kept at its default value. 

Bit 21 

TGF 

0x0 

rrc 

Transmitted Good Frames 
This  bit  is  set  when  the  transmitted  good  frame  counter 
reaches its maximum value or half its maximum value. 

Bit 20: 16  Reserved 

0x00 

resd 

Kept at its default value. 

Bit 15 

TGFMSC 

0x0 

rrc 

Transmitted Good Frames More Single Collision 
This bit is set when the transmitted good frame after more 
than a single collision counter reaches its maximum value 
or half its maximum value. 

Bit 14 

TSCGFCI   

0x0 

rrc 

Transmitted  Single  Collision  Good  Frame  Counter 
Interrupt) 
This  bit  is  set  when  the  transmitted  good  frame  after  a 
single collision counter reaches its maximum value or half 
its maximum value. 

Bit 13: 0 

Reserved 

0x0000 

resd 

Kept at its default value. 

Summary of Contents for AT32F435 Series





































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands