manualshive.com logo in svg

ARTERY AT32F435 Series, Reference Manual

Share
Download
ARTERY AT32F435 Series Reference Manual Download Page 408

  AT32F435/437

 

Series  Reference  Manual

 

2022.11.11

 

Page 408 

 

Rev 2.03

 

1: The new incoming message is discarded. 

Bit 2 

MMSSR 

0x0 

rw 

Multiple message transmit sequence rule 
0:  The  message  with  the  smallest  identifier  is  first 
transmitted. 
1:  The  message  with  the  first  request  order  is  first 
transmitted. 

Bit 1 

DZEN 

0x1 

rw 

Doze mode enable 
0: Sleep mode is disabled. 
1: Sleep mode is enabled. 
Note: 
The hardware will automatically leave sleep mode when 
the AEDEN is set and a message is monitored on the CAN 
bus. 
After CAN reset or partial software reset, this bit is forced 
to be set by hardware, that is, the CAN will keep in sleep 
mode, by default. 

Bit 0 

FZEN 

0x0 

rw 

Freeze mode enable 
0: Freeze mode disabled 
1: Freeze mode enabled 
Note: 
The  CAN  leaves  Freeze  mode  once  11  consecutive 
recessive bits have been detected on the RX pin. For this 
reason,  the  software  acknowledges  the  entry  of  Freeze 
mode after the FZC bit is cleared by hardware. 
The Freeze mode is entered only when the current CAN 
activity (transmission or reception) is completed. Thus the 
software acknowledges the exit of Freeze mode after the 
FZC bit is cleared by hardware. 

20.7.1.2 CAN master status register (CAN_MSTS) 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 12  Reserved 

0x00000 

resd 

Kept at its default value. 

Bit 11 

REALRX 

0x1 

ro 

Real time level on RX pin 
0: Low 
1: High 

Bit 10 

LSAMPRX 

0x1 

ro 

Last sample level on RX pin 
0: Low 
1: High 
  Note: This value keeps updating with the REALRX. 

Bit 9 

CURS 

0x0 

ro 

Current receive status 
0: No reception occurs 
1: Reception is in progress 
Note: This bit is set by hardware when the CAN reception 
starts,  and  it  is  cleared  by  hardware  at  the  end  of 
reception. 

Bit 8 

CUSS 

0x0 

ro 

Current transmit status 
0: No transmit occurs 
1: Transmit is in progress 
Note:  This  bit  is  set  by  hardware  when  the  CAN 
transmission starts, and it is cleared by hardware at the 
end of transmission. 

Bit 7: 5 

Reserved 

0x0 

resd 

Kept at its default value. 

Bit 4 

EDZIF 

0x0 

rw1c 

Enter doze mode interrupt flag 
0: Sleep mode is not entered or no condition for flag set. 
1: Sleep mode is entered. 
Note:   
This bit is set by hardware only when EDZIEN=1 and the 
CAN enters Sleep mode. When set, this bit will generate a 
status  change  interrupt.  This  bit  is  cleared  by  software 
(writing 1 to itself) or by hardware when DZC is cleared. 

Bit 3 

QDZIF 

0x0 

rw1c 

Exit doze mode interrupt flag 
0: Sleep mode is not left or no condition for exit. 
1:  Sleep  mode  has  been  left  or  exit  condition  has 
generated. 

Summary of Contents for AT32F435 Series





































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands