manualshive.com logo in svg

ARTERY AT32F435 Series, Reference Manual

Share
Download
ARTERY AT32F435 Series Reference Manual Download Page 535

  AT32F435/437

 

Series  Reference  Manual

 

2022.11.11

 

Page 535 

 

Rev 2.03

 

100: 1024 bytes 
Others: Reserved.

 

Bit 15 

NWASEN 

0x0 

rw 

NWAIT enable during asynchronous transfer   
0: NWAIT signal is disabled 
1: NWAIT signal is enable

 

Bit 14 

RWTD 

0x0 

rw 

Read-write timing different 
Different timings are used for read and write operations, 
that is, the XMC_BK1TMGWR register is enabled. 
0: Same timings for read and write operations 
1: Different timings for read and write operations

 

Bit 13 

NWSEN 

0x1 

rw 

NWAIT enable during synchronous transfer   
0: NWAIT signal is disabled 
1: NWAIT signal is enabled

 

Bit 12 

WEN 

0x1 

rw 

Write enable 
0: Disabled 
1: Enabled 

Bit 11 

NWTCFG 

0x0 

rw 

NWAIT timing configuration 
It is valid only in synchronous mode. 
0: NWAIT signal is active one data cycle before the wait   
state   
1: NWAIT signal is active one data cycle during the wait   
state

 

Bit 10 

WRAPEN 

0x0 

rw 

Wrapped enable 
This bit defines whether the XMC will split a wrapped AHB 
access into two accesses. 
0: Direct wrapped access is not allowed 
1: Direct wrapped access is allowed

 

Bit 9 

NWPOL 

0x0 

rw 

NWAIT polarity 
This  bit  defines  the  polarity  of  the  NWAIT  signal  in 
synchronous mode. 
0: NWAIT active low 
1: NWAIT active high

 

Bit 8 

SYNCBEN 

0x0 

rw 

Synchronous burst enable 
This bit allows synchronous access to Flash memories. 
0: Synchronous burst disabled 
1: Synchronous burst enabled

 

Bit 7 

Reserved 

0x1 

resd 

Kept at its default value. 

Bit 6 

NOREN 

0x1 

rw 

Nor flash access enable 
0: Nor flash access is disabled 
1: Nor flash access is enabled

 

Bit 5: 4 

EXTMDBW 

0x1 

rw 

External memory data bus width 
This field defines the external memory data bus width. 
00: 8 bits 
01: 16 bits 
10: Reserved 
11: Reserved

 

Bit 3: 2 

DEV 

0x0 

rw 

Memory device type 
00: SRAM/ROM 
01: PSRAM (Cellular RAM or CRAM) 
10: NOR Flash 
11: Reserved

 

Bit 1 

ADMUXEN 

0x1 

rw 

Address/data multiplexing enable 
0: Address/data not multiplexed 
1: Address/data multiplexed 

Bit 0 

EN 

0x0 

rw 

Memory bank enable 
0: Memory bank disabled 
1: Memory bank enabled 

Summary of Contents for AT32F435 Series





































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands