manualshive.com logo in svg

ARTERY AT32F435 Series, Reference Manual

Share
Download
ARTERY AT32F435 Series Reference Manual Download Page 323

  AT32F435/437

 

Series  Reference  Manual

 

2022.11.11

 

Page 323 

 

Rev 2.03

 

Bit 0 

OVFIF 

0x0 

rw0c 

Overflow interrupt flag 
This  bit  is  set  by  hardware  on  an  overflow  event.  It  is 
cleared by software. 
0: No overflow event occurs 
1:  Overflow  event  is  generated.  If  OVFEN=0  and 
OVFS=0 in the TMRx_CTRL1 register: 
−      An overflow event is  generated  when  OVFG= 1 in 
the TMRx_SWEVE register;   
−      An  overflow  event  is  generated  when  the  counter 
CVAL is reinitialized by a trigger event. 

14.4.4.6  TMR1, TMR8 and TMR20 software event register 

(TMRx_SWEVT) 

Bit 

Register 

Reset value 

Type 

Description 

Bit 15: 8 

Reserved 

0x000 

resd 

Kept at its default value. 

Bit 7 

BRKSWTR 

0x0 

wo 

Brake event triggered by software 
This bit is set by software to generate a brake event.   
0: No effect   
1: Generate a brake event. 

Bit 6 

TRGSWTR 

0x0 

rw 

Trigger event triggered by software 
This bit is set by software to generate a trigger event.   
0: No effect 
1: Generate a trigger event. 

Bit 5 

HALLSWTR 

0x0 

wo 

HALL event triggered by software 
This bit is set by software to generate a HALL event.   
0: No effect 
1: Generate a HALL event. 
Note:  This  bit  acts  only  on  channels  that  have 
complementary output. 

Bit 4 

C4SWTR 

0x0 

wo 

Channel 4 event triggered by software 
Please refer to C1M description. 

Bit 3 

C3SWTR 

0x0 

wo 

Channel 3 event triggered by software 
Please refer to C1M description. 

Bit 2 

C2SWTR 

0x0 

wo 

Channel 2 event triggered by software 
Please refer to C1M description 

Bit 1 

C1SWTR 

0x0 

wo 

Channel 1 event triggered by software 
This bit is set by software to generate a channel 1 event.   
0: No effect   
1: Generate a channel 1 event. 

Bit 0 

OVFSWTR 

0x0 

wo 

Overflow event triggered by software 
This bit is set by software to generate an overflow event.   
0: No effect   
1: Generate an overflow event. 

14.4.4.7  TMR1, TMR8 and TMR20 channel mode register1 (TMRx_CM1) 

The channel can be used in input (capture mode) or output (compare mode). The direction of a channel 
is defined by the corresponding CxC bits. All the other bits of this register have different functions in input 
and output modes. The CxOx describes its function in output mode when the channel is in output mode, 
while the CxIx describes its function in output mode when the channel is in input mode. Attention must 
be given to the fact that the same bit can have different functions in input mode and output mode. 

Output compare mode: 

Bit 

Register 

Reset value 

Type 

Description 

Bit 15 

C2OSEN 

0x0 

rw 

Channel 2 output switch enable 

Bit 14: 12 

C2OCTRL 

0x0 

rw 

Channel 2 output control 

Bit 11 

C2OBEN 

0x0 

rw 

Channel 2 output buffer enable 

Bit 10 

C2OIEN 

0x0 

rw 

Channel 2 output enable immediately 

Bit 9: 8 

C2C 

0x0 

rw 

Channel 2 configuration 
This field is used to define the direction of the channel 2 
(input  or  output),  and  the  selection  of  input  pin  when 
C2EN=’0’: 
00: Output 

Summary of Contents for AT32F435 Series





































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands