manualshive.com logo in svg

ARTERY AT32F435 Series, Reference Manual

Share
Download
ARTERY AT32F435 Series Reference Manual Download Page 163

  AT32F435/437

 

Series  Reference  Manual

 

2022.11.11

 

Page 163 

 

Rev 2.03

 

Bit 23: 19  REQCNT 

0x00 

rw 

DMA request count 
These bits indicate the number of DMA requests sent to 
the DMA controller after synchronization is enabled, and/or 
DMA request count before event output is generated. 
These  bits  are  reserved  only  when  both  SYNCEN  and 
EVTGEN bits are low. 

Bit 18: 17  SYNCPOL 

0x0 

rw 

Synchronization polarity 
This  field  defines  the  polarity  of  the  selected 
synchronization input. 
0x0: No events 
0x1: Rising edge 
0x2: Falling edge 
0x3: Rising edge and falling edge 

Bit 16 

SYNCEN 

0x0 

rw 

Synchronization enable 
0: Synchronization disabled 
1: Synchronization enabled 

Bit 15: 10  Reserved 

0x00 

resd 

Kept at its default value. 

Bit 9 

EVTGEN 

0x0 

 

Event generation enable 
0: Event generation is disabled 
1: Event generation is enabled 

Bit 8 

SYNCOVIEN 

0x0 

 

Synchronization overrun interrupt enable 
0: Interrupt disabled 
1: Interrupt enabled 

Bit 7 

Reserved 

0x0 

resd 

Kept at its default value. 

Bit 6: 0 

REQSEL 

0x00 

 

DMA request select 
Select  DMA  request.  Refer  to  DMAMUX  table  for  more 
information. 

9.5.9 

DMAMUX generator x control register 

(DMA_MUXGxCTRL) (x = 1

…

4)   

Access: 0 wait state, accessible by bytes, half-words or words. 
 

Bit   

Register 

Reset value 

Type 

Description 

Bit 31: 24  Reserved 

0x00 

resd 

Kept at its default value. 

Bit 23: 19  GREQCNT 

0x00 

rw 

DMA request generation count 
These bits define the number of DMA requests (GNBREQ 
+ 1) to be generated when a trigger event occurs.   
This field is reserved only when the GEN bit is disabled. 

Bit 18: 17  GPOL 

0x0 

rw 

DMA request generation polarity 
This field defines the polarity of the selected trigger input. 
0x0: No events 
0x1: Rising edge 
0x2: Falling edge 
0x3: Rising and falling edges 

Summary of Contents for AT32F435 Series





































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands