manualshive.com logo in svg

ARTERY AT32F435 Series, Reference Manual

Share
Download
ARTERY AT32F435 Series Reference Manual Download Page 629

  AT32F435/437

 

Series  Reference  Manual

 

2022.11.11

 

Page 629 

 

Rev 2.03

 

the  reception  command  were  issued  before  setting  the 
receive descriptor list address register, the DMA will show 
unpredictable behavior. 
When this bit is cleared, Rx DMA operation is stopped after 
the completion of a frame reception. The next descriptor 
position  in  the  receive  list  is  saved,  and  becomes  the 
current position when reception process is restarted. The 
Stop  Rece[topm  Command  is  effective  only  when  the 
receive  process  enters  in  the  running  state  (waiting  for 
receive packet) or the suspend state. 

Bit 0 

Reserved 

0x0 

resd 

Kept at its default value. 

26.3.28 Ethernet DMA interrupt enable register (EMAC_DMAIE)  

The EMAC_DMAIE register enables the interrupts reported by the status register. Setting a bit to 1’b1 
enables a corresponding interrupt. All interrupts are disabled after a software or hardware reset. 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 17  Reserved 

0x0000 

resd 

Kept at its default value. 

Bit 16 

NIE 

0x0 

rw 

Normal Interrupt enable 
When  this  bit  is  set,  a  normal  interrupt  summary  is 
enabled.  When  this  bit  is  cleared,  a  normal  interrupt 
summary is disabled. This bit enables the following bits (in 
the statue register) 
EMAC_DMASTS[0]: Transmit interrupt 
EMAC_DMASTS[2]: Transmit buffer unavailable 
EMAC_DMASTS[6]: Receive interrupt 
EMAC_DMASTS[14]: Early receive interrupt 

Bit 15 

AIE 

0x0 

rw 

Abnormal interrupt enable 
When  this  bit  is  set,  an  abnormal  interrupt  summary  is 
enabled. When  this  bit is  cleared, an abnormal  interrupt 
summary is disabled. This bit enables the following bits (in 
the status register) 
EMAC_DMASTS[1]: Transmit process stopped 
EMAC_DMASTS[3]: Transmit Jabber timeout 
EMAC_DMASTS[4]: Transmit overflow 
EMAC_DMASTS[5]: Transmit data underflow 
EMAC_DMASTS[7]: Transmit buffer u unavailable 
EMAC_DMASTS[8]: Receive process stopped 
EMAC_DMASTS[9]: Receive watchdog timeout 
EMAC_DMASTS[10]: Early transmit interrupt 
EMAC_DMASTS[13]: Fatal bus error 

Bit 14 

ERE 

0x0 

rw 

Early Receive interrupt Enable 
When  this  bit  is  set  with  the  normal  interrupt  summary 
enable bit, the early receive interrupt is enabled. When this 
bit is cleared, the early receive interrupt is disabled. 

Bit 13 

FBEE 

0x0 

rw 

Fatal Bus Error Enable 
When this bit is set with the abnormal interrupt summary 
enable bit, the fatal bus error interrupt is enabled. When 
this  bit  is  cleared,  the  fatal  bus  error  enable  interrupt  is 
disabled.

 

Bit 12: 11  Reserved 

0x0 

resd 

Kept at its default value. 

Bit 10 

EIE 

0x0 

rw 

Early transmit Interrupt Enable 
When this bit is set with the abnormal interrupt summary 
enable bit,  the  early  transmit  interrupt  is enabled. When 
this bit is cleared, the early transmit interrupt is disabled. 

Bit 9 

RWTE 

0x0 

rw 

Receive Watchdog Timeout Enable 
When this bit is set with the abnormal interrupt summary 
enable  bit,  the  receive  watchdog  timeout  interrupt  is 
enabled. When  this bit is cleared,  the  receive  watchdog 
timeout interrupt is disabled.

 

Bit 8 

RSE 

0x0 

rw 

Receive Stopped Enable 
When this bit is set with the abnormal interrupt summary 
enable bit, the receive stopped interrupt is enabled. When 
this bit is cleared, the receive stopped interrupt is disabled.

 

Summary of Contents for AT32F435 Series





































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands