manualshive.com logo in svg

ARTERY AT32F435 Series, Reference Manual

Share
Download
ARTERY AT32F435 Series Reference Manual Download Page 102

  AT32F435/437

 

Series  Reference  Manual

 

2022.11.11

 

Page 102 

 

Rev 2.03

 

Figure 5-3 

Flash memory mass erase process

 

Start

No

Check the OBF bit in FLASH_STSx

OBF = 0?

Yes

   Set BANKERS = 1 and ERSTR =1 

in FLASH_CTRLx

OBF = 0 ?

Check the OBF bit in FLASH_STSx

Read EPPERR bit and ODF bit in 

FLASH_STSx

No

Yes

End

 

5.2.3 

Programming operation 

The Flash memory can be programmed with 32 bits, 16 bits or 8 bits at a time. 
The following process is recommended: 

 

Check  the  OBF  bit  in  the  FLASH_STSx  register  to  confirm  that  there  is  no  other  programming 
operation in progress; 

 

Set  the  FPRGM  bit  in  the  FLASH_CTRLx  register,  so  that  the  Flash  memory  programming 
instructions can be received; 

 

Write the data (word/half-word/byte) to be programmed to the designated address; 

 

Wait until the OBF bit in the FLASH_STSx register becomes “0”, read the EPPERR, PRGMERR 
and ODF bit to verify the programming result. 

Note: 1. When the address to be written is not erased in advance, the programming operation is   

not executed unless the data to be written is all 0. In this case, a programming error is 
reported by the PRGMERR bit in the FLASH_STSx register. 
2. Read operation to the Flash memory during programming will halt CPU until the completion 
of programming. 

Summary of Contents for AT32F435 Series





































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands