manualshive.com logo in svg

ARTERY AT32F435 Series, Reference Manual

Share
Download
ARTERY AT32F435 Series Reference Manual Download Page 658

  AT32F435/437

 

Series  Reference  Manual

 

2022.11.11

 

Page 658 

 

Rev 2.03

 

Bit 2 

ESEIC 

0x0 

wo 

Embedded synchronization error interrupt clear 
Writing 1 to this bit clears the ESEES bit in the DVP_ESTS 
register,  and  clears  the  ESEIS  bit  in  the  DVP_ISTS 
register. 

Bit 1 

OVRIC 

0x0 

wo 

Output data FIFO overrun interrupt clear 
Writing 1 to this bit clears the OVRES bit in the DVP_ESTS 
register,  and  clears  the  OVRIS  bit  in  the  DVP_ISTS 
register. 

Bit 0 

CFDIC 

0x0 

wo 

Capture frame done interrupt clear 
Writing 1 to this bit clears the CFDES bit in the DVP_ESTS 
register,  and  clears  the  CFDIS  bit  in  the  DVP_ISTS 
register. 

27.8.7  DVP embedded synchronization code register (DVP_SCR) 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 24  FMEC 

0x00 

rw 

Frame end synchronization 4th code 
Frame  end  delimiter  code  consists  of  four  consecutive 
data: 
All 1, all 0, all 0, FE4 
Frame end delimiter 4

th

 code (FE4) is composed of FMEC. 

In  embedded  synchronization  mode,  if  the  FMEC  is 
programmed  to  0xFF,  the  decoder  performs  embedded 
synchronization for any frame end delimiter. 
All  the  undefined  bytes  other  than  FMSC,  LNSC  and 
LNEC are interpreted as frame end delimiter 4

th

 code FE4 

Bit 23: 16  LNEC 

0x00 

rw 

Line end synchronization 4th code 
The code consists of 4 consecutive data: 
All 1, all 0, all 0 and LE4 
Line end delimiter 4

th

 data (LE4) is composed of LNEC. 

Bit 15: 8 

LNSC 

0x00 

rw 

Line start synchronization 4th code 
The code consists of 4 consecutive data: 
All 1, all 0, all 0 and LS4 
Line start delimiter 4

th

 data (LS4) is composed of LNSC. 

Bit 7: 0 

FMSC 

0x00 

rw 

Frame start synchronization 4th code 
In  embedded  synchronization  mode,  if  the  FMSC  and 
FMSU  both  are  programmed  to  0xFF,  the  decoder 
performs  embedded  synchronization  for  non-frame-start 
synchronization code. 
The first occurrence of line start synchronization code after 
a Frame end code will be interpreted as a start of frame 
synchronization code. 

27.8.8  DVP embedded synchronization unmask register 
(DVP_SUR) 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 24  FMEU 

0x00 

rw 

Frame end synchronization code unmask 
This field specifies the mask to be applied to the code of 
the frame end synchronization.   
PDL=0, set bit N =0 in the FMEU, the bit N is masked 
PDL=1, set bit N =0 in the FMEU, the bit N+2 is masked 
PDL=2, set bit N =0 in the FMEU, the bit N+4 is masked 
PDL=2, set bit N =0 in the FMEU, the bit N+6 is masked

 

Bit 23: 16  LNEU 

0x00 

rw 

Line end synchronization code unmask 
This field specifies the mask to be applied to the code of 
the line end synchronization.   
PDL=0, set bit N =0 in the LNEU, the bit N is masked 
PDL=1, set bit N =0 in the LNEU, the bit N+2 is masked 
PDL=2, set bit N =0 in the LNEU, the bit N+4 is masked 
PDL=2, set bit N =0 in the LNEU, the bit N+6 is masked

 

Bit 15: 8 

LNSU 

0x00 

rw 

Line start synchronization code unmask 
This field specifies the mask to be applied to the code of 
the line end synchronization.   

Summary of Contents for AT32F435 Series





































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands