manualshive.com logo in svg

ARTERY AT32F435 Series, Reference Manual

Share
Download
ARTERY AT32F435 Series Reference Manual Download Page 619

  AT32F435/437

 

Series  Reference  Manual

 

2022.11.11

 

Page 619 

 

Rev 2.03

 

26.3.14 Ethernet MAC address 0 low register (EMAC_MACA0L)  

The Ethernet MAC address 0 low register contains the lower 32 bits of the 6-byte first MAC address. 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 0 

MA0L 

0xFFFF FFFF  rw 

MAC Address0 [31: 0] 
This field contains the lower 16 bits of the first 6-byte MCU 
address.  This  is  used  by  the  MAC  for  filtering  received 
frames, and for inserting the MAC address in the transmit 
flow control frames (Pause). 

26.3.15 Ethernet MAC address 1 high register (EMAC_MACA1H)  

The Ethernet MAC address 1 high register holds the upper 16 bits of the 6-byte second MAC address. 
If  the  MAC  address  register  is  configured  to  be  double-synchronized  with  the  MII  domain,  the 
synchronization can be enabled only by writing the bit [31: 24] (in little endian mode) or the bit [7: 0] (in 
big-endian mode) in the Ethernet MAC address 1 low register (EMAC_MACA1L) . Consecutive write 
operations to this address low register must be performed after at least 4 cycles in the destination clock 
domain so as to achieve an accurate synchronous update. 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31 

AE 

0x0 

rw 

Address Enable 
When  this  bit  is  set,  the  address  filter  uses  the  second 
MAC address for a perfect filtering. 
When this bit is cleared, the address filter will ignore the 
address for filtering. 

Bit 30 

SA 

0x0 

rw 

Source Address 
When this bit is set, the MAC address 1 [47: 0] is used for 
comparison with the source address field of the received 
frame. 
When this bit is cleared, the MAC address 1 [47: 0] is used 
for  comparison  with  the  destination  address  field  of  the 
received frame. 

Bit 29: 24  MBC 

0x00 

rw 

Mask Byte Control 
These bits are mask control bits for comparison with each 
of the MAC address bytes. 
When  this  bit  is  set,  the  MAC  does  not  compare  the 
corresponding  byte  of  the  received  DA/SA  with  the 
contents of the MAC address 1 register. Each control bit is 
used for controlling the mask of the bytes as follows: 
Bit 29: EMAC_MACA1H [15: 8] 
Bit 28: EMAC_MACA1H [7: 0] 
Bit 27: EMAC_MACA1L[31: 24] 
... 
Bit 24: EMAC_MACA1L[7: 0] 
It  is  possible  to  filter  group  addresses  (that  is,  group 
address  filtering)  by  masking  one  or  more  bytes  of  the 
address. 

Bit 23: 16  Reserved 

0x00 

resd 

Kept at its default value. 

Bit 15: 0 

MA1H 

0xFFFF 

rw 

MAC Address1 [47: 32] 
These bits contain the upper 16 bits (47: 32) of the 6-byte 
second MAC address.   

26.3.16 Ethernet MAC address 1 low register (EMAC_MACA1H)  

The Ethernet MAC address 1 low register contains the lower 32 bits of the 6-byte second MAC address. 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 0 

MA1L 

0xFFFF FFFF  rw 

MAC Address1 [31: 0]   
These bits contain the lower 32 bits of the 6-byte second 
MAC address. The contents of this field is undefined until 
loaded by the application after the initialization process. 

Summary of Contents for AT32F435 Series





































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands