![ABB ACS320 series User Manual Download Page 192](http://html.mh-extra.com/html/abb/acs320-series/acs320-series_user-manual_2965192.webp)
192 Actual signals and parameters
Group 21: Start/Stop
This group defines how the motor starts and stops. The drive supports several start
and stop modes.
Group 21: Start/Stop
Code
Description
Range
Resolution
Default
S
2101
START FUNCTION
1…7
1
6
Selects the motor start method.
1 = AUTO – The drive starts the motor instantly from zero frequency. If flying start is
required, use selection SCAN START.
2 = DC MAGN – The drive pre-magnetizes the motor with DC current before the start.
The pre-magnetizing time is defined by parameter
.
Note:
Starting to a rotating machine is not possible when DC MAGN is selected.
WARNING!
The drive will start after the set pre-magnetizing time has passed
even if the motor magnetization is not completed. Ensure always in applications
where a full break-away torque is essential, that the constant magnetizing time is long
enough to allow generation of full magnetization and torque.
4 = TORQ BOOST – Torque boost should be selected if a high break-away torque is
required.
The drive pre-magnetizes the motor with DC current before the start. The pre-
magnetizing time is defined by parameter
.
Torque boost is applied at start. Torque boost is stopped when output frequency
exceeds 20 Hz or when it is equal to the reference value. See parameter
.
Note:
Starting to a rotating machine is not possible when TORQ BOOST is selected.
WARNING!
The drive will start after the set pre-magnetizing time has passed
although the motor magnetization is not completed. Ensure always in
applications where a full break-away torque is essential, that the constant magnetizing
time is long enough to allow generation of full magnetization and torque.
6 = SCAN START – Frequency scanning flying start (starting the drive connected to a
rotating machine). Based on frequency scanning (interval
) to identify the frequency. If frequency
identification fails, DC magnetization is used (see selection DC MAGN).
7 = SCAN + BOOST – Combines scanning start (starting the drive connected to a
rotating machine) and torque boost. See selections SCANSTART and TORQ
BOOST. If frequency identification fails, torque boost is used.
2102
STOP FUNCTION
1, 2
1
1
Selects the motor stop method.
1 = COAST – Selects cutting off the motor power as the stop method. The motor
coasts to stop.
2 = RAMP – Selects using a deceleration ramp
• Deceleration ramp is defined by
(whichever is active).
Summary of Contents for ACS320 series
