manualshive.com logo in svg

Thermo Scientific Partisol 2000i, Инструкция по эксплуатации


Поделиться
Скачать
background image

Troubleshooting 

System Status 

11-2

     Partisol 2000

i

 and Partisol 2000

i

-D Instruction Manual 

Thermo Fisher Scientific 

 

Table 11–1.

 Diagnostic Menu Selections 

Menu Item 

Description 

Program 
Versions 

Shows the version numbers of the installed programs (read only). 

Voltages 

Displays the current diagnostic voltage readings (read only). 

Analog Input 
Readings 

Displays the eight user-scaled analog readings (if the I/O expansion board 
option is installed).  

Analog Input 
Voltages 

Displays the eight raw analog voltage readings (if the I/O expansion board 
option is installed). 

Digital Inputs 

Displays the state of the 16 digital inputs (read only). 

Relay States 

Displays the state of the ten digital outputs, eight solenoid outputs, and 
allows toggling of the state to either On (1) or Off (0). 

Test Analog 
Outputs 

Used to set each of the analog output channels to zero or full scale. Channel 
choices include all analog outputs, six voltage channels, and six current 
channels (if the I/O expansion board option is installed). 

Contact 
Information 

Displays telephone numbers of the customer service support centers. 

 

The System Status menu provides access to system troubleshooting 
information including status codes and alarms. The Status Codes screen 
displays a description of the currently active status conditions. Refer to 

Table 9–5

 on page 

9-63

 for a list of the status codes. 

●

 

In the Main Menu, choose System Status >

 Status Codes

. 

When an alarm is detected, the status of that associated item will go from 
OK to FAIL. The Alarms menu displays a list of items that are monitored 
by the Sampler. Refer to “

Alarms

” on page 

9-64

 for additional alarms 

information. 

●

 

In the Main Menu, choose System Status >

 Alarms

. 

This troubleshooting guide is designed to help isolate and identify 
instrument problems. 

Table 11–2

 provides general troubleshooting 

information and indicates the checks that you should perform if you 
experience an instrument problem.  

For additional service assistance, see “

Service Locations

” on page 

11-22

. 

System Status

Alarms

Troubleshooting

Guide

Содержание Partisol 2000i




















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Partisol 2000i

ICT SFM1 Quick Start Manual preview
SFM1
Бренд: ICT Страницы: 48
OfiTE 2040 Instruction Manual preview
2040
Бренд: OfiTE Страницы: 67
Bacharach 2810 Operation & Maintenance Manual preview
2810
Бренд: Bacharach Страницы: 28
Oldham MX15 Installation And Operating Instructions Manual preview
MX15
Бренд: Oldham Страницы: 22
Raytech MC2 Instruction Manual preview
MC2
Бренд: Raytech Страницы: 18
QUBINO Smart meter Manual preview
Smart meter
Бренд: QUBINO Страницы: 2
Wagner Meters Orion 910 Description And Instruction Manual preview
Orion 910
Бренд: Wagner Meters Страницы: 17
Fender P-Bass 27-6100 Manual preview
P-Bass 27-6100
Бренд: Fender Страницы: 20
YOKOGAWA Vigilant Plant MR20000 User Manual preview
Vigilant Plant MR20000
Бренд: YOKOGAWA Страницы: 230
Isspro R5441 Manual preview
R5441
Бренд: Isspro Страницы: 2
Lambda SRS SR475 Operation Manual preview
SRS SR475
Бренд: Lambda Страницы: 35
Cressi NEPTO Instruction Manual preview
NEPTO
Бренд: Cressi Страницы: 36
Lovibond Tintometer XD 7500 Quick Start Manual preview
Tintometer XD 7500
Бренд: Lovibond Страницы: 164
janitza 800-CT8-A Installation Instructions Manual preview
800-CT8-A
Бренд: janitza Страницы: 8
Kedida CT-6020 Instruction Manual preview
CT-6020
Бренд: Kedida Страницы: 4
ATD Tools ATD-3696 Instructions preview
ATD-3696
Бренд: ATD Tools Страницы: 2
Xylem mjk MagFlux Quick Start Manual preview
mjk MagFlux
Бренд: Xylem Страницы: 2
X-IO x-IMU3 User Manual preview
x-IMU3
Бренд: X-IO Страницы: 58

Бренды по названию

Популярные бренды

Загрузить еще бренды