manualshive.com logo in svg

Thermo Scientific Partisol 2000i, Инструкция по эксплуатации


Поделиться
Скачать
background image

Communications Using iPort or RPComm 

Using RPComm 

Thermo Fisher Scientific 

Partisol 2000

i

 and Partisol 2000

i

-D Instruction Manual     

D-29

 

10.

 

Choose “OK” from the Connection Type screen to finish the 
connection setup. 

11.

 

To initiate a modem connection to a selected instrument, highlight the 
connection name on the Connect List screen (

Figure D–20

) and select 

the Connection icon on the tool bar. The connection to the instrument 
will be initiated and the proper command codes sent. When 
communication is established, the Partisol 2000

i

 Main screen will be 

displayed (

Figure D–25

). 

Note  

If the connection is successful, the unit’s serial number will be 

displayed at the top of the screen. Ensure that the correct serial number is 
displayed to verify that the proper command codes were sent and that the 
serial port trigger is functioning properly. If the connection is not successful 
or if there is no instrument attached, then the serial number area will be 
blank or will display “99999.” If the modem loses its connection, wait at 
least 1 minute before trying to establish another connection. This allows 
the modem to reset itself. 

▲

  

12.

 

RPComm can now be used as described in “

RPComm

” on page 

D-1

. 

13.

 

To connect to a different instrument through the serial switching 
device, the current connection must be terminated. Enter the proper 
command codes for the desired instrument as described in step 7 and 
initiate the modem connection as explained in step 11. If the modem 
loses its connection, wait at least 1 minute before trying to establish 
another connection. This allows the modem to reset itself.  

Refer to this section if two or more 

i

Series instruments of different models 

are being connected to a serial switching device. The following 
combinations can be supported at this time: 

Series 1400a Monitor and a Partisol 2000

i

-D 

Partisol Model 2000 and a Partisol 2000

i

-D 

Although RPComm supports both the Series 1400a monitor and the 
Partisol Model 2000-FRM Sampler, it is not possible to connect these 
instruments to a single serial switching device. This is because the Series 
1400a monitor requires the local communication flow control to be set to 
“RTS/CTS” and the Partisol Model 2000-FRM monitor does not support 
any local communication flow control. If a Series 1400a monitor and a 
Partisol Model 2000-FRM Sampler are co-located, two modems and phone 
lines must be used for communications. 

Multiple Instruments of

Different Models

Содержание Partisol 2000i




















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Partisol 2000i

janitza UMG 96-PQ-L Installation Manual preview
UMG 96-PQ-L
Бренд: janitza Страницы: 12
janitza UMG 96-PA User Manual And Technical Data preview
UMG 96-PA
Бренд: janitza Страницы: 84
janitza UMG 96-PA Installation Instructions Manual preview
UMG 96-PA
Бренд: janitza Страницы: 6
janitza UMG 509-PRO Installation Instructions Manual preview
UMG 509-PRO
Бренд: janitza Страницы: 14
janitza UMG 96-PA User Manual And Technical Specifications preview
UMG 96-PA
Бренд: janitza Страницы: 98
Mahr MarSurf PS 10 Original Operating Instructions preview
MarSurf PS 10
Бренд: Mahr Страницы: 384
Olympus IPLEX TX Quick Manual preview
IPLEX TX
Бренд: Olympus Страницы: 4
R&S FSMR3000 User Manual preview
FSMR3000
Бренд: R&S Страницы: 733
R&S ZNH User Manual preview
ZNH
Бренд: R&S Страницы: 369
Facom DX.V12A Instruction Manual preview
DX.V12A
Бренд: Facom Страницы: 48
Grundfos Vortex Flow Industry Instructions Manual preview
Vortex Flow Industry
Бренд: Grundfos Страницы: 16
Spacelabs 91390 Operation Manual preview
91390
Бренд: Spacelabs Страницы: 156
RADWAG MA 3Y User Manual preview
MA 3Y
Бренд: RADWAG Страницы: 176
CARLO GAVAZZI WM14-96 - PROGRAMMING Instruction Manual preview
WM14-96 - PROGRAMMING
Бренд: CARLO GAVAZZI Страницы: 6
Caen V1724 Series Technical Information Manual preview
V1724 Series
Бренд: Caen Страницы: 63
Caen N957 Technical Information Manual preview
N957
Бренд: Caen Страницы: 35
Vega VEGACAP 65 Operating Instructions Manual preview
VEGACAP 65
Бренд: Vega Страницы: 44
Ocean Optics CHEM2000-UV-VIS Operating Manual And User Manual preview
CHEM2000-UV-VIS
Бренд: Ocean Optics Страницы: 42

Бренды по названию

Популярные бренды

Загрузить еще бренды