manualshive.com logo in svg

Thermo Scientific Partisol 2000i, Инструкция по эксплуатации


Поделиться
Скачать
background image

C-Link Protocol Commands 

Communications Configuration 

Thermo Fisher Scientific 

Partisol 2000

i

 and Partisol 2000

i

-D Instruction Manual     

B-23

 

addr ip 

This command reports the IP address of the analyzer. 

Send:  

addr 

ip 

Receive: 

addr ip 192.168.1.200 

 

set addr ip 

address

 

This command sets the analyzer’s IP 

address

, where 

address

 consists of four 

numbers ranging from 0-255 inclusive, separated by “.”. 

Note  

This command cannot be used when DHCP is on. Refer to the 

DHCP command that follows for additional information. 

▲

  

Send:   

set addr ip 192.168.1.200 

Receive: 

set addr ip 192.168.1.200 ok 

 

addr nm 

This command reports the IP netmask. 

Send:  

addr 

nm 

Receive: 

addr nm 255.255.255.0 

 

set addr nm 

address

 

This command sets the netmask 

address

, where 

address

 consists of four 

numbers ranging from 0-255 inclusive, separated by “.”. 

Note  

This command cannot be used when DHCP is on. Refer to the 

DHCP command that follows for additional information. 

▲

  

Send:   

set addr nm 255.255.255.0 

Receive: 

set addr nm 255.255.255.0 ok 

 

addr ntp 

This command reports the IP address for the network time protocol server. 
See “Network Time Protocol Server” in the Communications Settings” 
section of the “Operation” chapter for more information. 

Send:  

addr 

ntp 

Receive: 

addr ntp 10.209.43.237 

 

set addr ntp 

address

 

This command sets the network time protocol server 

address

, where 

address

 

consists of four numbers ranging from 0-255 inclusive, separated by “.”. 

Send:   

set addr ntp 10.209.43.237 

Receive: 

set addr ntp 10.209.43.237 ok 

Содержание Partisol 2000i




















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Partisol 2000i

ABQ Industrial TI-25MX Instruction Manual preview
TI-25MX
Бренд: ABQ Industrial Страницы: 15
ABQINDUSTRIAL HT-4000 User Manual preview
HT-4000
Бренд: ABQINDUSTRIAL Страницы: 3
Callaway 350TL Manual preview
350TL
Бренд: Callaway Страницы: 13
Hammond B-3 Owner'S Manual preview
B-3
Бренд: Hammond Страницы: 130
Keithley 485 Quick Reference Manual preview
485
Бренд: Keithley Страницы: 32
Idexx SediVue Dx User Manual preview
SediVue Dx
Бренд: Idexx Страницы: 6
IDEAL INDUSTRIES SignalTEK II Quick Reference Manual preview
SignalTEK II
Бренд: IDEAL INDUSTRIES Страницы: 10
M-system TR30 Instruction Manual preview
TR30
Бренд: M-system Страницы: 5
Blue-White FLEXFLO M4 Series Operating Manual preview
FLEXFLO M4 Series
Бренд: Blue-White Страницы: 64
Evoqua WALLACE & TIERNAN P7 ADVANCED Instruction Manual preview
WALLACE & TIERNAN P7 ADVANCED
Бренд: Evoqua Страницы: 98
Oldham MX 52 Commissioning, Operating And Maintenance Manual preview
MX 52
Бренд: Oldham Страницы: 96
A&D LCC07 Series Instruction Manual preview
LCC07 Series
Бренд: A&D Страницы: 2
Hammond XH-200 Basic Features Manual preview
XH-200
Бренд: Hammond Страницы: 106
SRS Labs SXMCMTU64 Installation Instructions Manual preview
SXMCMTU64
Бренд: SRS Labs Страницы: 11
NetThings Energy Manager Specification & Installation Manual preview
Energy Manager
Бренд: NetThings Страницы: 3
PowerMetrix PowerMaster MTA15Z Product Manual preview
PowerMaster MTA15Z
Бренд: PowerMetrix Страницы: 13
Erma Electronic SSI 3020 Instruction Manual preview
SSI 3020
Бренд: Erma Electronic Страницы: 24
PCE Instruments PCE-CMM 8 User Manual preview
PCE-CMM 8
Бренд: PCE Instruments Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды