manualshive.com logo in svg

Thermo Scientific Partisol 2000i, Инструкция по эксплуатации


Поделиться
Скачать
background image

Communications Using iPort or RPComm 

Using RPComm 

Thermo Fisher Scientific 

Partisol 2000

i

 and Partisol 2000

i

-D Instruction Manual     

D-35

 

36.

 

From the list of command codes on the right side of the AK Protocol 
Setup screen, select the correct series of command codes needed to 
trigger the desired instrument. As codes are chosen, they will appear on 
the bottom of the screen in the Connection Command box. If a code is 
entered incorrectly, it can be deleted by selecting the code in the 
Connection Command box and pressing the Delete key on your 
computer’s keyboard. 

37.

 

The remaining portions of the screen should have been set while 
establishing the modem connection. Do not modify these settings. 

38.

 

Select “OK” to exit the AK Protocol Setup screen. This will display the 
Connection Type screen. 

39.

 

Choose “OK” from the Connection Type screen to finish the 
connection setup. 

40.

 

Connect to one of the instruments by highlighting the connection 
name on the Connect List screen (

Figure D–20

) and select the 

Connection icon on the tool bar. The connection to the instrument 
will be initiated and the proper command codes sent. When 
communication is established, the instrument’s main screen will be 
displayed. 

Note  

If the connection is successful, the unit’s serial number will be 

displayed at the top of the screen. Ensure that the correct serial number is 
displayed to verify that the proper command codes were sent and that the 
serial port trigger is functioning properly. If the connection is not successful 
or if there is no instrument attached, then the serial number area will be 
blank or will display “99999.” If the modem loses its connection, wait at 
least 1 minute before trying to establish another connection. This allows 
the modem to reset itself. 

▲

  

41.

 

RPComm can now be used as described in “

RPComm

” on page 

D-1

.  

42.

 

To connect to the other instrument through the serial switching device, 
the current connection must be terminated. Enter the proper command 
codes for the desired instrument as described above and initiate the 
modem connection. If the modem loses its connection, wait at least 1 
minute before trying to establish another connection. This allows the 
modem to reset itself. 

Содержание Partisol 2000i




















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Partisol 2000i

Panasonic LP-400 Series External Control Manual preview
LP-400 Series
Бренд: Panasonic Страницы: 180
Labom BA Series Operating Instructions preview
BA Series
Бренд: Labom Страницы: 5
Yamaha AW2816 Tutorial preview
AW2816
Бренд: Yamaha Страницы: 31
Vectronics PM-30 Quick Manual preview
PM-30
Бренд: Vectronics Страницы: 4
Trotec BF06WP Operating Manual preview
BF06WP
Бренд: Trotec Страницы: 14
Kawai KSP 10 Owner'S Manual preview
KSP 10
Бренд: Kawai Страницы: 72
pts Diagnostics A1CNow Quick Reference Manual preview
A1CNow
Бренд: pts Diagnostics Страницы: 2
Spectroline LeakTracker OIL-GLO ULTRA Instruction Manual preview
LeakTracker OIL-GLO ULTRA
Бренд: Spectroline Страницы: 12
Vega VEGACAP 65 Operating Instructions Manual preview
VEGACAP 65
Бренд: Vega Страницы: 44
Novus NVR-7308P8-H2 User Manual preview
NVR-7308P8-H2
Бренд: Novus Страницы: 52
Rockler GRP41241 Instructions preview
GRP41241
Бренд: Rockler Страницы: 4
Charder HM201M User Manual preview
HM201M
Бренд: Charder Страницы: 12
Vaisala WAV252 Quick Reference Manual preview
WAV252
Бренд: Vaisala Страницы: 2
SKF 800030 Installation And Maintenance Manual preview
800030
Бренд: SKF Страницы: 12
Hall Research Technologies PGA-VHD User Manual preview
PGA-VHD
Бренд: Hall Research Technologies Страницы: 24
Samick SDP45 Owner'S Manual preview
SDP45
Бренд: Samick Страницы: 48
Badger Meter Orion 64989-002 Installation & Operation Manual preview
Orion 64989-002
Бренд: Badger Meter Страницы: 16
Macnaught M50 ST. STEEL SERIES Instruction Manual preview
M50 ST. STEEL SERIES
Бренд: Macnaught Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды