manualshive.com logo in svg

Thermo Scientific Partisol 2000i, Инструкция по эксплуатации


Поделиться
Скачать
background image

Sampler Operation 

Sampler Performance Verification 

7-2

     Partisol 2000

i

 and Partisol 2000

i

-D Instruction Manual 

Thermo Fisher Scientific 

The audit cassettes include an open test cassette p/n 36-012077 and a 
blocked test filter cassette p/n 36-012078. Prior to installing the filters 
or solid leak check discs in the cassettes, clean the filter cassettes with a 
clean cloth and alcohol to remove any oil or other material. Prepare the 
external leak check cassettes by installing clean, unused 47 mm filters 
into the filter cassette. Place the filter cassettes with 47 mm filters 
installed into the filter cassette carrier. Prepare the internal leak check 
cassette by installing a solid disk (36-004768) into the clean filter 
cassette. 

2.

 

If the Sampler is not already on, turn on the Sampler by pressing the 
power switch on the main panel to its “ON” position. The Sampler 
may be in the Stop Mode or in audit mode to perform the verification 
audits. If the Sampler is in the Stop Mode proceed with the verification 
audit. If the Sampler is running a sample and an audit must be 
performed, interrupt the sample by entering the audit mode. When the 
audit is completed, replace the current sample filter and resume the 
sample. 

3.

 

 Enter the Audit mode by pressing 

, scrolling to Audit and 

Calibration, and pressing 

 to display the Audit and Calibration 

menu. With the cursor at Audit Mode, press 

 to display the 

Audit Mode screen, press 

 to enter the Audit mode, and press 

 to confirm the setting. Press 

 to return to the Audit and 

Calibration menu. 

4.

 

If a sample filter is installed in the Sampler, remove the currently 
installed sample filter, in its filter cassette carrier, from the Sampler and 
store in the sample carrier box until the end of the audit. 

Use the following procedure to verify the ambient temperature measured 
by the Sampler: 

1.

 

Determine the current temperature (°C) at the ambient temperature 
sensor using an external thermometer [°C = 5/9 x (°F - 32)]. 

2.

 

Verify that the value of Amb Temp displayed in the Audit screen is 
within ±2 °C of the measured temperature. If the value is not within 
the limits, perform a calibration when the Sampler is not in Sample 
mode. 

Verifying the

Ambient Air

Temperature

Содержание Partisol 2000i




















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Partisol 2000i

Hameg HM8118 Operator'S Manual preview
HM8118
Бренд: Hameg Страницы: 44
Hameg HM8118 Manual preview
HM8118
Бренд: Hameg Страницы: 60
Hameg HM5014-2 Service Manual preview
HM5014-2
Бренд: Hameg Страницы: 28
HAMAR LASER STEALTH Series General Training Manual preview
STEALTH Series
Бренд: HAMAR LASER Страницы: 113
jablotron UC-260 Quick Start Manual preview
UC-260
Бренд: jablotron Страницы: 2
Jasco V-530 Hardware/Function Manual preview
V-530
Бренд: Jasco Страницы: 48
RADWAG PUE C32 Quick Start Manual preview
PUE C32
Бренд: RADWAG Страницы: 12
A&D MX-50 Instruction Manual preview
MX-50
Бренд: A&D Страницы: 39
Omega DP41-W User Manual preview
DP41-W
Бренд: Omega Страницы: 170
bentrup TM 100 Operating Instructions Manual preview
TM 100
Бренд: bentrup Страницы: 9
Mic 98871 Operation Manual preview
98871
Бренд: Mic Страницы: 2
Leica DISTOTM D5 Quick Start preview
DISTOTM D5
Бренд: Leica Страницы: 2
MATO DIGIMET E30 Preset Operating Instructions Manual preview
DIGIMET E30 Preset
Бренд: MATO Страницы: 20
Dive Gear Express DGX Gears XTRA Regulator Service Manual preview
DGX Gears XTRA Regulator
Бренд: Dive Gear Express Страницы: 26
Sper scientific 840060 Instruction Manual preview
840060
Бренд: Sper scientific Страницы: 12
Sherwood Scuba Scuba MAXIMUS SRB3600 regulator Assembly & Maintenance Manual preview
Scuba MAXIMUS SRB3600 regulator
Бренд: Sherwood Scuba Страницы: 29
Nauticam WIDE ANGLE CONVERSION PORT 2 Instruction Manual preview
WIDE ANGLE CONVERSION PORT 2
Бренд: Nauticam Страницы: 12
Kapro prolaser 891 User Manual preview
prolaser 891
Бренд: Kapro Страницы: 50

Бренды по названию

Популярные бренды

Загрузить еще бренды