manualshive.com logo in svg

Thermo Scientific Partisol 2000i, Инструкция по эксплуатации


Поделиться
Скачать
background image

Communications Using iPort or RPComm 

Using RPComm 

 

D-36

     Partisol 2000

i

 and Partisol 2000

i

-D Instruction Manual 

Thermo Fisher Scientific 

 

Use the following procedure to connect a Partisol Model 2000-FRM 
Sampler and a Partisol 2000

i

/2000

i

-D Sampler to a serial switching device. 

1.

 

Set up the Partisol 2000-FRM Sampler and Partisol 2000

i

/2000

i

-D 

Sampler for direct communications (“

Instrument Setup for Direct 

Communication

” on page 

D-4

).  

2.

 

Create a new connection to each instrument according to “

Creating a 

New Connection

” on page 

D-7

 and verify that the units are 

communicating properly. 

Note  

If the connection is successful, the unit’s serial number will be 

displayed at the top of the screen. If the connection is not successful or if 
there is no unit attached, then the serial number area will be blank or will 
display 99999. 

▲

  

3.

 

Once the RPComm software and instrument configurations have been 
verified, disconnect the direct connection. 

4.

 

Connect your computer directly to the modem that will be connected 
to the serial switching device (“

Standard Commercial External Modem 

Setup

” on page 

D-21

). 

5.

 

Begin executing any communication software which will allow direct 
communications with the modem. Communication software is usually 
included with most standard commercial modems. If no software 
program was included with your modem, Hyper Terminal (which is 
included with the Windows operating system) can be used. 

6.

 

Set the modem’s communication parameters to work with the Partisol 
2000

i

/2000

i

-D Sampler. A typical command string to send to the 

modem to configure it for use is:

 

AT &F0 &C0 &D0 S0=1 &K0 &W0 &Y0 

where: 

AT  

Command Prefix 

&F0   Software reset; restore default parameters 

&C0   Force DCD (Data Carrier Detect) “ON” at all times 

Connecting a Model 2000-

FRM and a Partisol

2000

i

/2000

i

-D Sampler

Содержание Partisol 2000i




















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Partisol 2000i

Calsense ET2000 Setup preview
ET2000
Бренд: Calsense Страницы: 4
DAKOTA ULTRASONICS MX-5 Operation Manual preview
MX-5
Бренд: DAKOTA ULTRASONICS Страницы: 48
TE Connectivity 832 Operating Manual preview
832
Бренд: TE Connectivity Страницы: 9
FARMSCAN Jackal v2 Manual preview
Jackal v2
Бренд: FARMSCAN Страницы: 28
Keithley 236 Service Manual preview
236
Бренд: Keithley Страницы: 138
Nady Audio ASM-2 User Manual preview
ASM-2
Бренд: Nady Audio Страницы: 2
Veeder-Root EMR4 Technical Installation Manual preview
EMR4
Бренд: Veeder-Root Страницы: 39
Veeder-Root TLS-450PLUS Install, Setup, & Operation Manual preview
TLS-450PLUS
Бренд: Veeder-Root Страницы: 98
VECTECH 496 Operation Manual preview
496
Бренд: VECTECH Страницы: 9
DriveTest BIA Class 2 Manual preview
BIA Class 2
Бренд: DriveTest Страницы: 24
Mannix DCFM8906 Operating Instructions preview
DCFM8906
Бренд: Mannix Страницы: 5
Neogen 9904A Quick Start Manual preview
9904A
Бренд: Neogen Страницы: 9
Toro Turf Guard Installation Setup Manual preview
Turf Guard
Бренд: Toro Страницы: 60
H.E. Anderson Ratio:Guard Advanced Manual preview
Ratio:Guard Advanced
Бренд: H.E. Anderson Страницы: 9
Caen V1724 Series Technical Information Manual preview
V1724 Series
Бренд: Caen Страницы: 63
Caen N957 Technical Information Manual preview
N957
Бренд: Caen Страницы: 35
Lutron Electronics VB-8213 Operation Manual preview
VB-8213
Бренд: Lutron Electronics Страницы: 23
odoland SP0810 Instruction Manual preview
SP0810
Бренд: odoland Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды