manualshive.com logo in svg

Thermo Scientific Partisol 2000i, Инструкция по эксплуатации


Поделиться
Скачать
background image

Sampler Operation 

Sampler Performance Verification 

7-10

     Partisol 2000

i

 and Partisol 2000

i

-D Instruction Manual 

Thermo Fisher Scientific 

7.

 

Press 

 to turn Off the flow. The measured flow should be within 

±5% of the displayed Current Flow. If this is not the case, perform the 
Flow Rate Calibration procedure. 

8.

 

To resume sampling, install or replace the sampling cassette with 
sampling filter installed. Reinstall the PM

10

 inlet on the sample tube.  

9.

 

Press 

 to restart the Sampler and continue the current sampling 

program. 

Use the following procedure to perform an internal leak check. This test 
will require a blocked test cassette p/n 36-012078. 

1.

 

Install the filter cassette carrier containing the filter cassette with 
blocked test cassette installed into the Sampler and push on the handle 
to move the filter cassette carrier into the sampling position. 

2.

 

Press 

 to return to the Audit and Calibration menu. 

3.

 

Scroll to Leak Checks, press 

, with the cursor at Internal, press 

. 

The following message displays: 

MAKE SURE THAT A LEAK CHECK DISK IS IN THE SAMPLE 
FILTER LOCATION!! 

Press 

 to begin testing. 

4.

 

A Pass or Fail message will display at the end of the leak check cycle. A 
pressure drop of 140 mmHg or less is the Sampler’s leak check pass 
criteria. Record the reading on the vacuum gauge. This reading should 
not drop by more than 140 mmHg during this 60 second period. This 
corresponds to a leak of 80 mL/min. If this reading does drop by more 
than 140 mmHg during this 60 second period, trace the internal flow 
paths to identify problems in tubing or connections. 

5.

 

If a Fail message is displayed, remove the filter cassette carrier and 
check the seals and repeat the leak check test. If the system fails the leak 
check a second time, the leak is before the test cassette. Isolate the the 
leak and repair. 

Internal Leak Check

Содержание Partisol 2000i




















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Partisol 2000i

Atomos Ninja Blade Quick Start Manual preview
Ninja Blade
Бренд: Atomos Страницы: 4
GE DigitalFlow GF868 Startup Manual preview
DigitalFlow GF868
Бренд: GE Страницы: 80
National Instruments NI 9219 Getting Started Manual preview
NI 9219
Бренд: National Instruments Страницы: 38
Keithley 600A Instruction Manual preview
600A
Бренд: Keithley Страницы: 31
Keithley 610B Instruction Manual preview
610B
Бренд: Keithley Страницы: 63
Keithley 4200A-SCS Quick Start Manual preview
4200A-SCS
Бренд: Keithley Страницы: 18
Keithley 445 Instruction Manual preview
445
Бренд: Keithley Страницы: 73
Cecomp F20B Instruction Manual preview
F20B
Бренд: Cecomp Страницы: 4
ISKRAEMECO MT174 Manual preview
MT174
Бренд: ISKRAEMECO Страницы: 12
Ravaglioli RAVTD1760WS Series Service Manual preview
RAVTD1760WS Series
Бренд: Ravaglioli Страницы: 24
Ratek TH8000 User Manual preview
TH8000
Бренд: Ratek Страницы: 25
Magtrol 6510e User Manual preview
6510e
Бренд: Magtrol Страницы: 76
Flexim 990735-1 User Manual preview
990735-1
Бренд: Flexim Страницы: 160
Neriox 111456 Operating Instructions Manual preview
111456
Бренд: Neriox Страницы: 10
3M SP-SE-2-1/1 User Manual preview
SP-SE-2-1/1
Бренд: 3M Страницы: 168
T&D MCR-4V User Manual preview
MCR-4V
Бренд: T&D Страницы: 31
Blue-White industries Sonic-Pro S6A Series Quick Start Manual preview
Sonic-Pro S6A Series
Бренд: Blue-White industries Страницы: 2
FMT Swiss AG NUMERIxx3 Operating Instructions Manual preview
NUMERIxx3
Бренд: FMT Swiss AG Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды