manualshive.com logo in svg

Thermo Scientific Partisol 2000i, Инструкция по эксплуатации


Поделиться
Скачать
background image

Preventive Maintenance 

Virtual Impactor Maintenance Partisol 2000i-D 

10-12

     Partisol 2000

i

 and Partisol 2000

i

-D Instruction Manual 

Thermo Fisher Scientific 

12.

 

Screw the top of the WINS impactor back onto the bottom section. 
Ensure that the WINS impactor remains in the upright orientation so 
that the oil in the impactor assembly does not spill. 

13.

 

Multiple WINS impactors can be prepared in this manner at one time 
and kept for later use. 

Use the following procedure to reinstall the WINS Impactor: 

1.

 

Attach the adapter to the lower section of the WINS impactor. 

2.

 

Push the WINS impactor (with its adapter attached) upward into the 
WINS impactor mounting sleeve. 

3.

 

Pass the rollers of the filter exchange mechanism through the slots in 
the left-hand and right-hand guides. 

4.

 

Allow the filter exchange mechanism to open fully. 

5.

 

Insert the filter cassette carrier (with a filter cassette installed) into the 
filter platform by matching the slot and hole in the filter cassette carrier 
with the appropriate hardware. 

6.

 

Push the handle of the filter exchange mechanism toward the back to 
install the filter cassette. 

7.

 

Perform a system leak check. 

8.

 

If in the Audit mode, at the Main Menu, select Audit and Calibration 
> Audit Mode, and press 

 to turn off the Audit mode. 

Use the following procedures to remove, clean, and reinstall the virtual 
impactor that is used in the Partisol 2000

i

-D Sampler.  

Virtual impactor maintenance and performance verification can be 
performed while in the Stop, Wait, or Sampling modes. If the Sampler is in 
the Stop Mode, press 

 and select Audit and Calibration > Audit 

Mode, and press 

 to change to the Audit mode. 

WINS Impactor

Reinstallation

Virtual Impactor 

Maintenance

Partisol 2000

i

-D

Содержание Partisol 2000i




















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Partisol 2000i

ABB Navigator 550 Commissioning Instructions preview
Navigator 550
Бренд: ABB Страницы: 8
GE Mentor Visual iQ Quick Start Manual preview
Mentor Visual iQ
Бренд: GE Страницы: 2
Kawai DG30 Setting Manual preview
DG30
Бренд: Kawai Страницы: 19
Calculated Industries 6425 User Manual preview
6425
Бренд: Calculated Industries Страницы: 64
Nady Audio ASM-2 User Manual preview
ASM-2
Бренд: Nady Audio Страницы: 2
Flytec Element Track Quick Manual preview
Element Track
Бренд: Flytec Страницы: 2
TASKING MPC5X Hardware User Manual preview
MPC5X
Бренд: TASKING Страницы: 12
ESP LTD KH-602 Owner'S Manual & Warranty Information preview
LTD KH-602
Бренд: ESP Страницы: 12
E+H Micropilot S FMR533 Manual preview
Micropilot S FMR533
Бренд: E+H Страницы: 12
National Instruments AT-AI-16XE-10 Programmer'S Manual preview
AT-AI-16XE-10
Бренд: National Instruments Страницы: 169
Kawai CN34 Software Update preview
CN34
Бренд: Kawai Страницы: 2
Cable Ferret FERRET CF2810C Instruction Manual preview
FERRET CF2810C
Бренд: Cable Ferret Страницы: 16
Hanna Instruments HI6421P Quick Reference Manual preview
HI6421P
Бренд: Hanna Instruments Страницы: 2
i-PRO WJ-NX310K Series Important Information Manual preview
WJ-NX310K Series
Бренд: i-PRO Страницы: 18
CWT GFM A0A0161 Operation & Installation Manual preview
GFM A0A0161
Бренд: CWT Страницы: 41
Audio Precision APx555 Installation Instructions And Specifications preview
APx555
Бренд: Audio Precision Страницы: 98
Maxtec UltraMaxO2 Operating Manual & Instructions For Use preview
UltraMaxO2
Бренд: Maxtec Страницы: 13
janitza MRG 512 PQ Flex Operation Manual preview
MRG 512 PQ Flex
Бренд: janitza Страницы: 9

Бренды по названию

Популярные бренды

Загрузить еще бренды