manualshive.com logo in svg

Thermo Scientific Partisol 2000i, Инструкция по эксплуатации


Поделиться
Скачать
background image

Sampler Operation 

Sampler Performance Verification 

Thermo Fisher Scientific 

Partisol 2000

i

 and Partisol 2000

i

-D Instruction Manual     

7-7

 

9.

 

If not performing a flow verification, restore the sampling hardware to 
its original state by removing the flow metering hardware and 
reinstalling the PM

10

 inlet on the sample tube. Remove the filter 

cassette from the Sampler and discard the installed filter. 

Perform the temperature verification, pressure verification, and a leak check 
before performing the flow verification procedure. 

Note  

Ensure that the filter cassette carrier previously installed in the 

Sampler (which was used to perform the external leak check) remains in the 
unit for the flow verification. 

▲

  

While the flow verification procedures are similar for the Partisol 2000

i

 and 

Partisol 2000

i

-D, since the Partisol 2000

i

-D Sampler uses two flow sensors 

to control the sample flows for the PM

2.5

 and PM

coarse

 flow channels, the 

verification procedures are presented for each Sampler. 

Note  

If you are using a Streamline Pro MultiCal System or other direct 

reading flow audit device, follow these instructions. If using a Streamline 
FTS, follow the instructions later in the manual. The proper values for the 
Streamline FTS constants can be entered into the Sampler for proper 
calculation of the measured flow values. 

▲

  

If you are not using the Streamline Pro or FTS systems to audit the flow of 
the Samper, you may need to install the flow audit adapter (57-000618) 
onto the end of the sample tube (

Figure 7–5

). If you will be using the flow 

audit adapter, ensure that you install it onto the end of the sample tube 
with its valve in the open position. 

Flow controllers require a 15 minute warm-up prior to first reading. All 
subsequent readings should be taken 2-3 minutes (minimum) 
thereafter. 

Use the following procedure to perform a flow audit on the Partisol 2000

i

: 

1.

 

Remove the flow audit adapter used during the leak check and install 
the Streamline Pro on the sample tube (

Figure 7–6

). Other flow meters 

may require the use of the flow audit adapter (valve open) to measure 
flow. 

Flow Verification

Flow Audit/Verification –

Partisol 2000

i

Содержание Partisol 2000i




















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Partisol 2000i

Omega Engineering DFG35 Series User Manual preview
DFG35 Series
Бренд: Omega Engineering Страницы: 22
Keithley 617 Quick Reference Manual preview
617
Бренд: Keithley Страницы: 55
i-SENS KetoSens User Manual preview
KetoSens
Бренд: i-SENS Страницы: 50
ILX Lightwave OMM-6810B User Manual preview
OMM-6810B
Бренд: ILX Lightwave Страницы: 126
Alfa Laval TE67D 1 Series Instruction Manual preview
TE67D 1 Series
Бренд: Alfa Laval Страницы: 18
Primes Cube L1 Original Instructions Manual preview
Cube L1
Бренд: Primes Страницы: 56
PASCO PASPORT PS-2174 Instruction Sheet preview
PASPORT PS-2174
Бренд: PASCO Страницы: 4
Unipro UniGo 3005 Quick Manual preview
UniGo 3005
Бренд: Unipro Страницы: 2
OTOVATION Amplitude T Series Installation Manual preview
Amplitude T Series
Бренд: OTOVATION Страницы: 15
X-Rite RapidMatch GO User Manual preview
RapidMatch GO
Бренд: X-Rite Страницы: 21
DeNovix DS-11 FX+ User Manual preview
DS-11 FX+
Бренд: DeNovix Страницы: 93
Charder HM201M User Manual preview
HM201M
Бренд: Charder Страницы: 12
LaserLiner DuoView Camera Manual preview
DuoView Camera
Бренд: LaserLiner Страницы: 64
fos4X Blackbird OECD MDE0835 Instructions For Use Manual preview
Blackbird OECD MDE0835
Бренд: fos4X Страницы: 80
ECEFAST DH-TDS100H Instruction Manual preview
DH-TDS100H
Бренд: ECEFAST Страницы: 93
Omega BS6050 Instruction Sheet preview
BS6050
Бренд: Omega Страницы: 2
Starr Instruments TGD-100 Instructions Manual preview
TGD-100
Бренд: Starr Instruments Страницы: 29
Sierra InnovaSonic 205i Instruction Manual preview
InnovaSonic 205i
Бренд: Sierra Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды