manualshive.com logo in svg

Thermo Scientific Partisol 2000i, Инструкция по эксплуатации


Поделиться
Скачать
background image

Communications Using iPort or RPComm 

Using RPComm 

Thermo Fisher Scientific 

Partisol 2000

i

 and Partisol 2000

i

-D Instruction Manual     

D-41

 

37.

 

The remaining portions of the screen should have been set while 
establishing the modem connection. Do not modify these settings.  

38.

 

Select “OK” to exit the AK Protocol Setup screen. This will display the 
Connection Type screen. 

39.

 

Choose “OK” from the Connection Type screen to finish the 
connection setup. 

40.

 

Connect to one of the instruments by highlighting the connection 
name on the Connect List screen (

Figure D–20

) and select the 

Connection icon on the tool bar. The connection to the instrument 
will be initiated and the proper command codes sent. When 
communication is established, the instrument’s main screen will be 
displayed. 

Note  

If the connection is successful, the unit’s serial number will be 

displayed at the top of the screen. Ensure that the correct serial number is 
displayed to verify that the proper command codes were sent and that the 
serial port trigger is functioning properly. If the connection is not successful 
or if there is no instrument attached, then the serial number area will be 
blank or will display “99999.” If the modem loses its connection, wait at 
least 1 minute before trying to establish another connection. This allows 
the modem to reset itself. 

▲

  

41.

 

RPComm can now be used as described in “

RPComm

” on page 

D-1

.  

42.

 

To connect to the other instrument through the serial switching device, 
the current connection must be terminated. Enter the proper command 
codes for the desired instrument as described above and initiate the 
modem connection. If the modem loses its connection, wait at least 1 
minute before trying to establish another connection. This allows the 
modem to reset itself. 

 

 

Содержание Partisol 2000i




















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Partisol 2000i

Kawai ES3 Specifications preview
ES3
Бренд: Kawai Страницы: 2
Datron 1061 Calibration And Servicing Handbook preview
1061
Бренд: Datron Страницы: 197
A&D MF-50 Instruction Manual preview
MF-50
Бренд: A&D Страницы: 74
Oceanic EOS Service Procedure preview
EOS
Бренд: Oceanic Страницы: 17
Hameg HM8118 Operator'S Manual preview
HM8118
Бренд: Hameg Страницы: 44
Hameg HM8118 Manual preview
HM8118
Бренд: Hameg Страницы: 60
Hameg HM5014-2 Service Manual preview
HM5014-2
Бренд: Hameg Страницы: 28
HAMAR LASER STEALTH Series General Training Manual preview
STEALTH Series
Бренд: HAMAR LASER Страницы: 113
Oakton 150 Series Operating Instructions preview
150 Series
Бренд: Oakton Страницы: 4
YOKOGAWA SC21 Series Instruction Manual preview
SC21 Series
Бренд: YOKOGAWA Страницы: 16
Sage SIP Operation And Instruction Manual preview
SIP
Бренд: Sage Страницы: 68
Kawai DX800 Owner'S Manual preview
DX800
Бренд: Kawai Страницы: 40
Fender P-Bass 27-6100 Manual preview
P-Bass 27-6100
Бренд: Fender Страницы: 20
RIDGID micro CA-350 Operator'S Manual preview
micro CA-350
Бренд: RIDGID Страницы: 18
socomec DIRIS Digiware D-40 Instruction Manual preview
DIRIS Digiware D-40
Бренд: socomec Страницы: 58
IDEAL 61-737 Operation And Safety Manual preview
61-737
Бренд: IDEAL Страницы: 84
Ratek TH8000 User Manual preview
TH8000
Бренд: Ratek Страницы: 25
Reed Instruments 800837000736 Instruction Manual preview
800837000736
Бренд: Reed Instruments Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды