manualshive.com logo in svg

Thermo Scientific Partisol 2000i, Инструкция по эксплуатации


Поделиться
Скачать
background image

Operational Modes 

Partisol Operational Modes 

5-2

     Partisol 2000

i

 and Partisol 2000

i

-D Instruction Manual 

Thermo Fisher Scientific 

 

While in the Sampling mode, the Sampler is currently in a user-defined 
sampling interval. Except in the case of Advanced sampling with 
conditions, the unit will draws ambient air in through its sampling system 
at the volumetric flow rates specified by the user. For the Partisol 2000

i

 the 

default flow rate is 16.67 L/min and for the Partisol 2000

i

-D the default 

flow is 1.67 L/min for the coarse flow channel and 15 L/min for the fine 
flow channel. The sample will continue unless the sample flow rates deviate 
from their set points by 10% or more for more than 60 seconds or until the 
ending time/date is reached. 

If the sample flow rate deviates from the defined setpoints, the unit will 
enter the Error mode and it will stop sampling. The software will register 
an “S1” Status Code and remain until the user resets the unit. 

Pressing 

, when in the Sampling mode, offers the user the choice of 

entering the Audit mode (for exchanging or cleaning the inlets or 
performing a Sampler audit) or the Stop mode. 

Once the ending time/date is reached, the unit automatically enters the 
Done Operating Mode if the current status code is “Ok,” or enters the 
Error Operating Mode if the Sampler has encountered a status condition 
(See 

Status Codes

 on page 

9-62

). Editing of sample information is not 

allowed in this mode. 

The Sampler enters Done at the completion of its sampling program if it 
encountered no status conditions during sample collection (that force the 
end of sampling). Pressing 

 with the run screen displayed with the 

hardware in this mode causes the Sampler to return to the Stop Operating 
Mode. 

Note  

Do not exchange filter cassettes with the Sampler in Done mode. 

Return to the Stop Operating Mode before exchanging the collection 
media. 

▲

  

 

The Sampler proceeds to Err mode at the completion of its sampling 
program if it encountered a status condition during sample collection 
(status code is not “Ok”), or if it encounters the flow rate deviation 
condition, “S1” (See 

Status Codes

 on page 

9-62

). Pressing 

 in the 

Main screen with the hardware in this mode causes the Sampler to return 
to the Stop Operating Mode. 

Sampling Mode

Done Mode

Error Mode

Содержание Partisol 2000i




















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Partisol 2000i

Valeport 803 Operating Manual preview
803
Бренд: Valeport Страницы: 25
Oakton PC 300 Instruction Manual preview
PC 300
Бренд: Oakton Страницы: 69
QuantAsylum QA401 User Manual preview
QA401
Бренд: QuantAsylum Страницы: 70
Underground Magnetics Mag 3 Operator'S Manual preview
Mag 3
Бренд: Underground Magnetics Страницы: 48
Pasco Scientific Precision 2.0 Instruction Manual And Experiment Manual preview
Precision 2.0
Бренд: Pasco Scientific Страницы: 11
Topcon CA-200F Instructions For Use Manual preview
CA-200F
Бренд: Topcon Страницы: 62
DAKOTA ULTRASONICS ZX-5 Instruction Manual preview
ZX-5
Бренд: DAKOTA ULTRASONICS Страницы: 50
Jamar Radar Recorder Quick Start Manual preview
Radar Recorder
Бренд: Jamar Страницы: 4
Larson Davis SoundTrack LxT N/Forcer Field Operation Manual preview
SoundTrack LxT N/Forcer
Бренд: Larson Davis Страницы: 12
Mark-10 ME-100 User Manual preview
ME-100
Бренд: Mark-10 Страницы: 26
Trebs 99732 Manual preview
99732
Бренд: Trebs Страницы: 44
Textron Greenlee CLM-1000 Manual preview
Greenlee CLM-1000
Бренд: Textron Страницы: 36
janitza UMG 96-PA User Manual preview
UMG 96-PA
Бренд: janitza Страницы: 85
Feature tech AW06A User Manual preview
AW06A
Бренд: Feature tech Страницы: 2
MADDALENA Arrow Mobile Android Quick Start Manual preview
Arrow Mobile Android
Бренд: MADDALENA Страницы: 12
Kabelmat MESSBOI 25 Operating Manual preview
MESSBOI 25
Бренд: Kabelmat Страницы: 27
Halcyon Multifunction Compensator Owner'S Manual preview
Multifunction Compensator
Бренд: Halcyon Страницы: 20
XS Instruments 60 VioLab Series Instruction Manual preview
60 VioLab Series
Бренд: XS Instruments Страницы: 41

Бренды по названию

Популярные бренды

Загрузить еще бренды