NEC V850E/IA1 mPD703116 Скачать руководство пользователя страница 79

Страница: 79 / 832

CHAPTER 3 CPU FUNCTION

User’s Manual U14492EJ3V0UD

3.4.7 Recommended use of address space

The architecture of the V850E/IA1 requires that a register that serves as a pointer be secured for address

generation when accessing operand data in the data space. Operand data access from instruction can be directly

executed at the address in this pointer register ±32 KB. However, because there is a limit to which general-purpose

registers are used as a pointer register, by minimizing the deterioration of address calculation performance when

changing the pointer value, the number of usable general-purpose registers for handling variables is maximized, and

the program size can be saved.

To enhance the efficiency of using the pointer in connection with the memory map of the V850E/IA1, the following

points are recommended:

(1) Program space

Of the 32 bits of the program counter (PC), the higher 6 bits are fixed to 0, and only the lower 26 bits are

valid. Therefore, a contiguous 64 MB space, starting from address 00000000H, unconditionally corresponds

to the memory map of the program space.

(2) Data space

For the efficient use of resources that make use of the wrap-around feature of the data space, the continuous

16 MB address spaces 00000000H to 00FFFFFFH and FF000000H to FFFFFFFFH of the 4 GB CPU are

used as the data space. With the V850E/IA1, a 256 MB physical address space is seen as 16 images in the

4 GB CPU address space. The highest bit (bit 25) of this 26-bit address is assigned as address sign-

extended to 32 bits.

Example

Application of wrap-around

00007FFFH

(R =) 00000000H

FFFFE7FFH

FFFF8000H

Internal ROM area

On-chip peripheral

I/O area

External memory

area

FFFFF000H
FFFFEFFFH

FFFFBFFFH

FFFFE800H

FFFFC000H

Internal RAM area

32 KB

4 KB

10 KB

16 KB

0003FFFFH

When R = r0 (zero register) is specified with the LD/ST disp16 [R] instruction, an addressing range of

00000000H ±32 KB can be referenced with the sign-extended disp16. By mapping the external memory in

the 16 KB area in the figure, all resources including internal hardware can be accessed with one pointer.

The zero register (r0) is a register set to 0 by the hardware, and eliminates the need for additional registers

for the pointer.

Содержание V850E/IA1 mPD703116

































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание V850E/IA1 mPD703116

Отзывы:

Похожие инструкции для V850E/IA1 mPD703116

Бренды по названию

Популярные бренды

NEC V850E/IA1 mPD703116, Руководство пользователя

Результаты поиска

Содержание V850E/IA1 mPD703116

Отзывы:

Похожие инструкции для V850E/IA1 mPD703116

Бренды по названию

Популярные бренды